| [6] | 1 | /**
|
|---|
| 2 | ******************************************************************************
|
|---|
| 3 | * File Name : gpio.c
|
|---|
| 4 | * Description : This file provides code for the configuration
|
|---|
| 5 | * of all used GPIO pins.
|
|---|
| 6 | ******************************************************************************
|
|---|
| 7 | * @attention
|
|---|
| 8 | *
|
|---|
| 9 | * <h2><center>© Copyright (c) 2019 STMicroelectronics.
|
|---|
| 10 | * All rights reserved.</center></h2>
|
|---|
| 11 | *
|
|---|
| 12 | * This software component is licensed by ST under BSD 3-Clause license,
|
|---|
| 13 | * the "License"; You may not use this file except in compliance with the
|
|---|
| 14 | * License. You may obtain a copy of the License at:
|
|---|
| 15 | * opensource.org/licenses/BSD-3-Clause
|
|---|
| 16 | *
|
|---|
| 17 | ******************************************************************************
|
|---|
| 18 | */
|
|---|
| 19 |
|
|---|
| 20 | /* Includes ------------------------------------------------------------------*/
|
|---|
| 21 | #include "gpio.h"
|
|---|
| 22 | /* USER CODE BEGIN 0 */
|
|---|
| 23 | #include "ads1260.h"
|
|---|
| 24 | /* USER CODE END 0 */
|
|---|
| 25 |
|
|---|
| 26 | /*----------------------------------------------------------------------------*/
|
|---|
| 27 | /* Configure GPIO */
|
|---|
| 28 | /*----------------------------------------------------------------------------*/
|
|---|
| 29 | /* USER CODE BEGIN 1 */
|
|---|
| 30 |
|
|---|
| 31 | /* USER CODE END 1 */
|
|---|
| 32 |
|
|---|
| 33 | /** Configure pins as
|
|---|
| 34 | * Analog
|
|---|
| 35 | * Input
|
|---|
| 36 | * Output
|
|---|
| 37 | * EVENT_OUT
|
|---|
| 38 | * EXTI
|
|---|
| 39 | */
|
|---|
| 40 | void MX_GPIO_Init(void)
|
|---|
| 41 | {
|
|---|
| 42 |
|
|---|
| 43 | GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|---|
| 44 |
|
|---|
| 45 | /* GPIO Ports Clock Enable */
|
|---|
| 46 | __HAL_RCC_GPIOB_CLK_ENABLE();
|
|---|
| 47 | __HAL_RCC_GPIOC_CLK_ENABLE();
|
|---|
| 48 | __HAL_RCC_GPIOF_CLK_ENABLE();
|
|---|
| 49 | __HAL_RCC_GPIOA_CLK_ENABLE();
|
|---|
| 50 |
|
|---|
| 51 | /*Configure GPIO pin Output Level */
|
|---|
| 52 | HAL_GPIO_WritePin(GPIOA, ADC_RESET_Pin|ADC_START_CONV_Pin
|
|---|
| 53 | #ifndef MCO_TEST_FUNCTION
|
|---|
| 54 | |OVP_ENABLE_Pin
|
|---|
| 55 | #endif
|
|---|
| 56 | |LVP_ENABLE_Pin|LED_FUNCTION_Pin|LED_ERROR_Pin, GPIO_PIN_RESET);
|
|---|
| 57 |
|
|---|
| 58 | //HAL_GPIO_WritePin(GPIOB, ADC_POWER_DOWN_Pin, GPIO_PIN_RESET);
|
|---|
| 59 |
|
|---|
| 60 | /*Configure GPIO pin Output Level */
|
|---|
| 61 | HAL_GPIO_WritePin(AUX_EN_GPIO_Port, AUX_EN_Pin, GPIO_PIN_RESET);
|
|---|
| 62 |
|
|---|
| 63 | /*Configure GPIO pin : PtPin */
|
|---|
| 64 | GPIO_InitStruct.Pin = ADC_DATA_READY_Pin;
|
|---|
| 65 | GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
|
|---|
| 66 | GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|---|
| 67 | HAL_GPIO_Init(ADC_DATA_READY_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 68 |
|
|---|
| 69 |
|
|---|
| 70 |
|
|---|
| 71 | /*Configure GPIO pins : PAPin PAPin PAPin PAPin
|
|---|
| 72 | PAPin PAPin PAPin PAPin
|
|---|
| 73 | PAPin */
|
|---|
| 74 | GPIO_InitStruct.Pin = ADC_RESET_Pin|ADC_START_CONV_Pin
|
|---|
| 75 | #ifndef MCO_TEST_FUNCTION
|
|---|
| 76 | |OVP_ENABLE_Pin
|
|---|
| 77 | #endif
|
|---|
| 78 | |LVP_ENABLE_Pin|LED_FUNCTION_Pin|LED_ERROR_Pin ;
|
|---|
| 79 | GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|---|
| 80 | GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|---|
| 81 | GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|---|
| 82 | HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|---|
| 83 |
|
|---|
| 84 |
|
|---|
| 85 | /*Configure GPIO pin : PtPin */
|
|---|
| 86 | GPIO_InitStruct.Pin = BUTTON_Pin;
|
|---|
| 87 | GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
|---|
| 88 | GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|---|
| 89 | HAL_GPIO_Init(BUTTON_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 90 |
|
|---|
| 91 | /*Configure GPIO pin : PtPin */
|
|---|
| 92 | GPIO_InitStruct.Pin = AUX_EN_Pin;
|
|---|
| 93 | GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|---|
| 94 | GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|---|
| 95 | GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|---|
| 96 | HAL_GPIO_Init(AUX_EN_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 97 |
|
|---|
| 98 | // EDIT ECS
|
|---|
| 99 | // Reservierter Pin wird zu restore Factory beim Startup
|
|---|
| 100 | // Funktion wenn ber Jumper auf Masse gesetzt
|
|---|
| 101 | //GPIO_InitStruct.Pin = RESERVED_1_Pin;
|
|---|
| 102 | //GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
|---|
| 103 | //GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|---|
| 104 | //GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|---|
| 105 | //HAL_GPIO_Init(RESERVED_1_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 106 |
|
|---|
| 107 | //GPIO_InitStruct.Pin = ADC_POWER_DOWN_Pin;
|
|---|
| 108 | //GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|---|
| 109 | //GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|---|
| 110 | //GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|---|
| 111 | //HAL_GPIO_Init(ADC_POWER_DOWN_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 112 |
|
|---|
| 113 | GPIO_InitStruct.Pin = ADC_RESET_Pin;
|
|---|
| 114 | GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|---|
| 115 | GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|---|
| 116 | GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|---|
| 117 | HAL_GPIO_Init(ADC_RESET_GPIO_Port, &GPIO_InitStruct);
|
|---|
| 118 | }
|
|---|
| 119 |
|
|---|
| 120 | /* USER CODE BEGIN 2 */
|
|---|
| 121 | void HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin)
|
|---|
| 122 | {
|
|---|
| 123 | if (GPIO_Pin == ADC_DATA_READY_Pin)
|
|---|
| 124 | {
|
|---|
| 125 | newCurrentValue=1;
|
|---|
| 126 |
|
|---|
| 127 |
|
|---|
| 128 | }
|
|---|
| 129 | }
|
|---|
| 130 | /* USER CODE END 2 */
|
|---|
| 131 |
|
|---|
| 132 | /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
|---|
