source: trunk/firmware/SES/Drivers/EEPROM/flash_interface.c

/**
  ******************************************************************************
  * @file    EEPROM_Emul/Porting/STM32G0/flash_interface.c
  * @author  MCD Application Team
  * @brief   This file provides all the EEPROM emulation flash interface functions.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2020 STMicroelectronics International N.V.
  * All rights reserved.</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without
  * modification, are permitted, provided that the following conditions are met:
  *
  * 1. Redistribution of source code must retain the above copyright notice,
  *    this list of conditions and the following disclaimer.
  * 2. Redistributions in binary form must reproduce the above copyright notice,
  *    this list of conditions and the following disclaimer in the documentation
  *    and/or other materials provided with the distribution.
  * 3. Neither the name of STMicroelectronics nor the names of other
  *    contributors to this software may be used to endorse or promote products
  *    derived from this software without specific written permission.
  * 4. This software, including modifications and/or derivative works of this
  *    software, must execute solely and exclusively on microcontroller or
  *    microprocessor devices manufactured by or for STMicroelectronics.
  * 5. Redistribution and use of this software other than as permitted under
  *    this license is void and will automatically terminate your rights under
  *    this license.
  *
  * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT
  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
  * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY
  * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT
  * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
  * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
  * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
  * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
  * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
  * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "eeprom_emul.h"
#include "flash_interface.h"

/** @addtogroup EEPROM_Emulation
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @addtogroup EEPROM_Private_Functions
  * @{
  */

/**
  * @brief  Write a double word at the given address in Flash
  * @param  Address Where to write
  * @param  Data What to write
  * @retval EE_Status
  *           - EE_OK: on success
  *           - EE_WRITE_ERROR: if an error occurs
  */
HAL_StatusTypeDef FI_WriteDoubleWord(uint32_t Address, uint64_t Data)
{
  return HAL_FLASH_Program(FLASH_TYPEPROGRAM_DOUBLEWORD, Address, Data); 
}
    
/**
  * @brief  Erase a page in polling mode
  * @param  Page Page number
  * @param  NbPages Number of pages to erase
  * @retval EE_Status
  *           - EE_OK: on success
  *           - EE error code: if an error occurs
  */
EE_Status FI_PageErase(uint32_t Page, uint16_t NbPages)
{
  EE_Status status = EE_OK;
  FLASH_EraseInitTypeDef s_eraseinit;
  uint32_t page_error = 0U;

  s_eraseinit.TypeErase   = FLASH_TYPEERASE_PAGES;
  s_eraseinit.NbPages     = NbPages;
  s_eraseinit.Page        = Page;

  /* Erase the Page: Set Page status to ERASED status */
  if (HAL_FLASHEx_Erase(&s_eraseinit, &page_error) != HAL_OK)
  {
    status = EE_ERASE_ERROR;
  }
  return status;
}

/**
  * @brief  Erase a page with interrupt enabled
  * @param  Page Page number
  * @param  NbPages Number of pages to erase
  * @retval EE_Status
  *           - EE_OK: on success
  *           - EE error code: if an error occurs
  */
EE_Status FI_PageErase_IT(uint32_t Page, uint16_t NbPages)
{
  EE_Status status = EE_OK;
  FLASH_EraseInitTypeDef s_eraseinit;

  s_eraseinit.TypeErase   = FLASH_TYPEERASE_PAGES;
  s_eraseinit.NbPages     = NbPages;
  s_eraseinit.Page        = Page;

  /* Erase the Page: Set Page status to ERASED status */
  if (HAL_FLASHEx_Erase_IT(&s_eraseinit) != HAL_OK)
  {
    status = EE_ERASE_ERROR;
  }
  return status;
}

/**
  * @brief  Delete corrupted Flash address, can be called from NMI. No Timeout.
  * @param  Address Address of the FLASH Memory to delete
  * @retval EE_Status
  *           - EE_OK: on success
  *           - EE error code: if an error occurs
  */
EE_Status FI_DeleteCorruptedFlashAddress(uint32_t Address)
{
  EE_Status status = EE_OK;

  /* Set FLASH Programmation bit */
  SET_BIT(FLASH->CR, FLASH_CR_PG);

  /* Program double word of value 0 */
  *(__IO uint32_t*)(Address) = (uint32_t)0U;
  *(__IO uint32_t*)(Address+4U) = (uint32_t)0U;

  /* Wait programmation completion */
  while(__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY))
  {
  }

  /* Check if error occured */
  if((__HAL_FLASH_GET_FLAG(FLASH_FLAG_OPERR))  || (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PROGERR)) ||
     (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)) || (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR))  ||
     (__HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR)) || (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGSERR)))
  {
    status = EE_DELETE_ERROR;
  }

  /* Check FLASH End of Operation flag  */
  if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
  {
    /* Clear FLASH End of Operation pending bit */
    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
  }

  /* Clear FLASH Programmation bit */
  CLEAR_BIT(FLASH->CR, FLASH_CR_PG);

  /* Clear FLASH ECCD bit */
  __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_ECCD);

  return status;
}

/**
  * @brief  Check if the configuration is 128-bits bank or 2*64-bits bank
  * @param  None
  * @retval EE_Status
  *           - EE_OK: on success
  *           - EE error code: if an error occurs
  */
EE_Status FI_CheckBankConfig(void)
{
#if defined (FLASH_OPTR_DBANK)
  FLASH_OBProgramInitTypeDef sOBCfg;
  EE_Status status;

  /* Request the Option Byte configuration :
     - User and RDP level are always returned
     - WRP and PCROP are not requested */
  sOBCfg.WRPArea     = 0xFF;
  sOBCfg.PCROPConfig = 0xFF;
  HAL_FLASHEx_OBGetConfig(&sOBCfg);

  /* Check the value of the DBANK user option byte */
  if ((sOBCfg.USERConfig & OB_DBANK_64_BITS) != 0)
  {
    status = EE_OK;
  }
  else
  {
    status = EE_INVALID_BANK_CFG;
  }

  return status;
#else
  /* No feature 128-bits single bank, so always 64-bits dual bank */
  return EE_OK;
#endif
}


/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/