source: ctrl/firmware/Main/CubeMX/Core/Inc

Revision Log Mode:


Legend:

Added
Modified
Copied or renamed
Diff Rev Age Author Log Message
(edit) @114   18 months Zed Fixing the project.
(edit) @113   19 months Zed Added CAN bus support.
(edit) @112   19 months Zed Fixing project. Need to add CAN in CubeMX.
(edit) @111   20 months Zed Fixing project.
(edit) @110   20 months Zed Fixing project.
(edit) @109   20 months Zed Fixing project.
(edit) @108   20 months Zed Fixing project.
(edit) @107   20 months Zed Everything works good. Fixing project.
(edit) @106   20 months Zed Fixing project.
(edit) @98   20 months Zed Charging PWM on TIM1 was implemented.
(edit) @97   21 months Zed DAC works.
(edit) @96   21 months Zed ADC3 with DMA was implemented. DTS was activated.
(edit) @95   21 months Zed Fixing project.
(edit) @94   21 months Zed Fixing project.
(edit) @92   21 months Zed Fixing project before changing MPU settings in CubeMX.
(edit) @91   21 months Zed ADC module was activated.
(edit) @89   21 months Zed Added basic I2C EEPROM support.
(edit) @88   21 months Zed BME280 data transfer works ok. Device returns its ID 0x60.
(edit) @87   21 months Zed RTC is working.
(edit) @86   21 months Zed
(edit) @84   21 months Zed Added TIM6 in CubeMX to generate 1µs delays for 1-Wire Protocol.
(edit) @82   21 months Zed DMA transfer to µSD-card was implemented.
(edit) @81   21 months Zed Modbus Master and Slave interfaces were added.
(edit) @79   21 months Zed DHCP client can get IP-address from fritz!box
(edit) @77   21 months Zed LwIP was removed from the project.
(edit) @76   21 months Zed Fixing project before changing NSS control for SPI2 in CubeMX.
(edit) @73   21 months Zed FreeRTOS can be compiled without errors.
(edit) @72   21 months Zed FreeRTOS was added to the project.
(edit) @70   21 months Zed AZRTOS and NetX were removed from the project.
(edit) @66   21 months Zed FAN PWM control and TACHO signal measuring are working.
(edit) @64   22 months Zed USART3 TX DMA is working.
(edit) @63   22 months Zed Fixing project.
(edit) @62   22 months Zed GSM STATUS pin is working.
(edit) @61   22 months Zed GSM thread was added.
(edit) @58   23 months Zed POWER_ENABLE lines for 4V, 5V, 10V and 15V were tested.
(edit) @56   23 months Zed Tick rate was changed to 1000 in CubeMX.
(edit) @54   23 months Zed SDMMC(DMA) and Azure_RTOS(with FileX) are activated.
(edit) @51   23 months Zed SDMMC low level driver was added.
(edit) @50   23 months Zed LED control description were added.
(edit) @48   23 months Zed Backlight was turned on for Display.
(edit) @47   23 months Zed
(edit) @45   23 months Zed Added SPI module for Display.
(edit) @39   23 months Zed RTC module was activated.
(edit) @13   2 years Zed Forgot to add to the project these files.
(add) @11   2 years Zed
Note: See TracRevisionLog for help on using the revision log.