Index: ctrl/firmware/Main/CubeMX/Core/Inc/i2c.h =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Inc/i2c.h (revision 88) +++ ctrl/firmware/Main/CubeMX/Core/Inc/i2c.h (revision 88) @@ -0,0 +1,52 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file i2c.h + * @brief This file contains all the function prototypes for + * the i2c.c file + ****************************************************************************** + * @attention + * + * Copyright (c) 2025 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ +/* USER CODE END Header */ +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __I2C_H__ +#define __I2C_H__ + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "main.h" + +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +extern I2C_HandleTypeDef hi2c1; + +/* USER CODE BEGIN Private defines */ + +/* USER CODE END Private defines */ + +void MX_I2C1_Init(void); + +/* USER CODE BEGIN Prototypes */ + +/* USER CODE END Prototypes */ + +#ifdef __cplusplus +} +#endif + +#endif /* __I2C_H__ */ + Index: ctrl/firmware/Main/CubeMX/Core/Inc/main.h =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Inc/main.h (revision 87) +++ ctrl/firmware/Main/CubeMX/Core/Inc/main.h (revision 88) @@ -126,4 +126,8 @@ #define ETH_SPI_NSS_Pin GPIO_PIN_4 #define ETH_SPI_NSS_GPIO_Port GPIOB +#define BME_I2C_SCL_Pin GPIO_PIN_6 +#define BME_I2C_SCL_GPIO_Port GPIOB +#define BME_I2C_SDA_Pin GPIO_PIN_7 +#define BME_I2C_SDA_GPIO_Port GPIOB #define ETH_SPI_INT_Pin GPIO_PIN_8 #define ETH_SPI_INT_GPIO_Port GPIOB Index: ctrl/firmware/Main/CubeMX/Core/Src/freertos.c =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Src/freertos.c (revision 87) +++ ctrl/firmware/Main/CubeMX/Core/Src/freertos.c (revision 88) @@ -36,4 +36,5 @@ #include "beeper_task.h" #include "onewire_task.h" +#include "bme_task.h" /* USER CODE END Includes */ @@ -53,4 +54,5 @@ #define BEEPER_TASK_STACK_DEPTH_WORDS (128U) #define ONEWIRE_TASK_STACK_DEPTH_WORDS (128U) +#define BME_TASK_STACK_DEPTH_WORDS (256U) /* USER CODE END PD */ @@ -69,4 +71,5 @@ static StackType_t beeperTaskStackBuffer[BEEPER_TASK_STACK_DEPTH_WORDS] __attribute__((section(".DTCM_RAM"))); static StackType_t onewireTaskStackBuffer[ONEWIRE_TASK_STACK_DEPTH_WORDS] __attribute__((section(".DTCM_RAM"))); +static StackType_t bmeTaskStackBuffer[BME_TASK_STACK_DEPTH_WORDS] __attribute__((section(".DTCM_RAM"))); static uint8_t beeperQueueStorageArea[BEEPER_QUEUE_SIZE * BEEPER_QUEUE_ITEM_SIZE] __attribute__((section(".DTCM_RAM"))); @@ -78,4 +81,5 @@ static StaticTask_t beeperTaskBuffer __attribute__((section(".DTCM_RAM"))); static StaticTask_t onewireTaskBuffer __attribute__((section(".DTCM_RAM"))); +static StaticTask_t bmeTaskBuffer __attribute__((section(".DTCM_RAM"))); static StaticQueue_t beeperQueueBuffer __attribute__((section(".DTCM_RAM"))); @@ -87,5 +91,5 @@ static const char* const beeperTaskName = "BeeperTask"; static const char* const onewireTaskName = "1WireTask"; - +static const char* const bmeTaskName = "BMETask"; /* USER CODE END Variables */ @@ -190,4 +194,7 @@ if (r == NULL) printf("Cannot create %s!\n", onewireTaskName); + r = xTaskCreateStatic(bmeTaskStart, bmeTaskName, BME_TASK_STACK_DEPTH_WORDS, NULL, 24, bmeTaskStackBuffer, &bmeTaskBuffer); + if (r == NULL) printf("Cannot create %s!\n", bmeTaskName); + /* USER CODE END RTOS_THREADS */ Index: ctrl/firmware/Main/CubeMX/Core/Src/gpio.c =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Src/gpio.c (revision 87) +++ ctrl/firmware/Main/CubeMX/Core/Src/gpio.c (revision 88) @@ -128,9 +128,7 @@ /*Configure GPIO pins : PB0 PB1 PB2 PB11 - PB12 PB13 PB3 PB5 - PB6 PB7 */ + PB12 PB13 PB3 PB5 */ GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_11 - |GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_3|GPIO_PIN_5 - |GPIO_PIN_6|GPIO_PIN_7; + |GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_3|GPIO_PIN_5; GPIO_InitStruct.Mode = GPIO_MODE_ANALOG; GPIO_InitStruct.Pull = GPIO_NOPULL; Index: ctrl/firmware/Main/CubeMX/Core/Src/i2c.c =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Src/i2c.c (revision 88) +++ ctrl/firmware/Main/CubeMX/Core/Src/i2c.c (revision 88) @@ -0,0 +1,140 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file i2c.c + * @brief This file provides code for the configuration + * of the I2C instances. + ****************************************************************************** + * @attention + * + * Copyright (c) 2025 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ +/* USER CODE END Header */ +/* Includes ------------------------------------------------------------------*/ +#include "i2c.h" + +/* USER CODE BEGIN 0 */ + +/* USER CODE END 0 */ + +I2C_HandleTypeDef hi2c1; + +/* I2C1 init function */ +void MX_I2C1_Init(void) +{ + + /* USER CODE BEGIN I2C1_Init 0 */ + + /* USER CODE END I2C1_Init 0 */ + + /* USER CODE BEGIN I2C1_Init 1 */ + + /* USER CODE END I2C1_Init 1 */ + hi2c1.Instance = I2C1; + hi2c1.Init.Timing = 0x10707DBC; + hi2c1.Init.OwnAddress1 = 0; + hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; + hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; + hi2c1.Init.OwnAddress2 = 0; + hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK; + hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; + hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; + if (HAL_I2C_Init(&hi2c1) != HAL_OK) + { + Error_Handler(); + } + + /** Configure Analogue filter + */ + if (HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE) != HAL_OK) + { + Error_Handler(); + } + + /** Configure Digital filter + */ + if (HAL_I2CEx_ConfigDigitalFilter(&hi2c1, 0) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN I2C1_Init 2 */ + + /* USER CODE END I2C1_Init 2 */ + +} + +void HAL_I2C_MspInit(I2C_HandleTypeDef* i2cHandle) +{ + + GPIO_InitTypeDef GPIO_InitStruct = {0}; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0}; + if(i2cHandle->Instance==I2C1) + { + /* USER CODE BEGIN I2C1_MspInit 0 */ + + /* USER CODE END I2C1_MspInit 0 */ + + /** Initializes the peripherals clock + */ + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_I2C1; + PeriphClkInitStruct.I2c123ClockSelection = RCC_I2C1235CLKSOURCE_HSI; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK) + { + Error_Handler(); + } + + __HAL_RCC_GPIOB_CLK_ENABLE(); + /**I2C1 GPIO Configuration + PB6 ------> I2C1_SCL + PB7 ------> I2C1_SDA + */ + GPIO_InitStruct.Pin = BME_I2C_SCL_Pin|BME_I2C_SDA_Pin; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; + GPIO_InitStruct.Alternate = GPIO_AF4_I2C1; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /* I2C1 clock enable */ + __HAL_RCC_I2C1_CLK_ENABLE(); + /* USER CODE BEGIN I2C1_MspInit 1 */ + + /* USER CODE END I2C1_MspInit 1 */ + } +} + +void HAL_I2C_MspDeInit(I2C_HandleTypeDef* i2cHandle) +{ + + if(i2cHandle->Instance==I2C1) + { + /* USER CODE BEGIN I2C1_MspDeInit 0 */ + + /* USER CODE END I2C1_MspDeInit 0 */ + /* Peripheral clock disable */ + __HAL_RCC_I2C1_CLK_DISABLE(); + + /**I2C1 GPIO Configuration + PB6 ------> I2C1_SCL + PB7 ------> I2C1_SDA + */ + HAL_GPIO_DeInit(BME_I2C_SCL_GPIO_Port, BME_I2C_SCL_Pin); + + HAL_GPIO_DeInit(BME_I2C_SDA_GPIO_Port, BME_I2C_SDA_Pin); + + /* USER CODE BEGIN I2C1_MspDeInit 1 */ + + /* USER CODE END I2C1_MspDeInit 1 */ + } +} + +/* USER CODE BEGIN 1 */ + +/* USER CODE END 1 */ Index: ctrl/firmware/Main/CubeMX/Core/Src/main.c =================================================================== --- ctrl/firmware/Main/CubeMX/Core/Src/main.c (revision 87) +++ ctrl/firmware/Main/CubeMX/Core/Src/main.c (revision 88) @@ -22,4 +22,5 @@ #include "dma.h" #include "fatfs.h" +#include "i2c.h" #include "mdma.h" #include "memorymap.h" @@ -140,4 +141,5 @@ MX_USART10_UART_Init(); MX_TIM6_Init(); + MX_I2C1_Init(); /* USER CODE BEGIN 2 */ @@ -193,7 +195,10 @@ * in the RCC_OscInitTypeDef structure. */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE|RCC_OSCILLATORTYPE_LSE; + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSE + |RCC_OSCILLATORTYPE_LSE; RCC_OscInitStruct.HSEState = RCC_HSE_ON; RCC_OscInitStruct.LSEState = RCC_LSE_ON; + RCC_OscInitStruct.HSIState = RCC_HSI_DIV1; + RCC_OscInitStruct.HSICalibrationValue = 64; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; @@ -246,5 +251,5 @@ PeriphClkInitStruct.PLL3.PLL3P = 2; PeriphClkInitStruct.PLL3.PLL3Q = 8; - PeriphClkInitStruct.PLL3.PLL3R = 2; + PeriphClkInitStruct.PLL3.PLL3R = 4; PeriphClkInitStruct.PLL3.PLL3RGE = RCC_PLL3VCIRANGE_0; PeriphClkInitStruct.PLL3.PLL3VCOSEL = RCC_PLL3VCOMEDIUM; Index: ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c.c =================================================================== --- ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c.c (revision 88) +++ ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c.c (revision 88) @@ -0,0 +1,7544 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_i2c.c + * @author MCD Application Team + * @brief I2C HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Inter Integrated Circuit (I2C) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral State and Errors functions + * + ****************************************************************************** + * @attention + * + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The I2C HAL driver can be used as follows: + + (#) Declare a I2C_HandleTypeDef handle structure, for example: + I2C_HandleTypeDef hi2c; + + (#)Initialize the I2C low level resources by implementing the HAL_I2C_MspInit() API: + (##) Enable the I2Cx interface clock + (##) I2C pins configuration + (+++) Enable the clock for the I2C GPIOs + (+++) Configure I2C pins as alternate function open-drain + (##) NVIC configuration if you need to use interrupt process + (+++) Configure the I2Cx interrupt priority + (+++) Enable the NVIC I2C IRQ Channel + (##) DMA Configuration if you need to use DMA process + (+++) Declare a DMA_HandleTypeDef handle structure for + the transmit or receive stream or channel depends on Instance + (+++) Enable the DMAx interface clock using + (+++) Configure the DMA handle parameters + (+++) Configure the DMA Tx or Rx stream or channel depends on Instance + (+++) Associate the initialized DMA handle to the hi2c DMA Tx or Rx handle + (+++) Configure the priority and enable the NVIC for the transfer complete interrupt on + the DMA Tx or Rx stream or channel depends on Instance + + (#) Configure the Communication Clock Timing, Own Address1, Master Addressing mode, Dual Addressing mode, + Own Address2, Own Address2 Mask, General call and Nostretch mode in the hi2c Init structure. + + (#) Initialize the I2C registers by calling the HAL_I2C_Init(), configures also the low level Hardware + (GPIO, CLOCK, NVIC...etc) by calling the customized HAL_I2C_MspInit(&hi2c) API. + + (#) To check if target device is ready for communication, use the function HAL_I2C_IsDeviceReady() + + (#) For I2C IO and IO MEM operations, three operation modes are available within this driver : + + *** Polling mode IO operation *** + ================================= + [..] + (+) Transmit in master mode an amount of data in blocking mode using HAL_I2C_Master_Transmit() + (+) Receive in master mode an amount of data in blocking mode using HAL_I2C_Master_Receive() + (+) Transmit in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Transmit() + (+) Receive in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Receive() + + *** Polling mode IO MEM operation *** + ===================================== + [..] + (+) Write an amount of data in blocking mode to a specific memory address using HAL_I2C_Mem_Write() + (+) Read an amount of data in blocking mode from a specific memory address using HAL_I2C_Mem_Read() + + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Transmit in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Transmit_IT() + (+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() + (+) Receive in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Receive_IT() + (+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() + (+) Transmit in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Transmit_IT() + (+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() + (+) Receive in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Receive_IT() + (+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() + (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can + add their own code by customization of function pointer HAL_I2C_ErrorCallback() + (+) Abort a master or memory I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() + (+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_AbortCpltCallback() + (+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. + This action will inform Master to generate a Stop condition to discard the communication. + + + *** Interrupt mode or DMA mode IO sequential operation *** + ========================================================== + [..] + (@) These interfaces allow to manage a sequential transfer with a repeated start condition + when a direction change during transfer + [..] + (+) A specific option field manage the different steps of a sequential transfer + (+) Option field values are defined through I2C_XFEROPTIONS and are listed below: + (++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functional is same as associated interfaces in + no sequential mode + (++) I2C_FIRST_FRAME: Sequential usage, this option allow to manage a sequence with start condition, address + and data to transfer without a final stop condition + (++) I2C_FIRST_AND_NEXT_FRAME: Sequential usage (Master only), this option allow to manage a sequence with + start condition, address and data to transfer without a final stop condition, + an then permit a call the same master sequential interface several times + (like HAL_I2C_Master_Seq_Transmit_IT() then HAL_I2C_Master_Seq_Transmit_IT() + or HAL_I2C_Master_Seq_Transmit_DMA() then HAL_I2C_Master_Seq_Transmit_DMA()) + (++) I2C_NEXT_FRAME: Sequential usage, this option allow to manage a sequence with a restart condition, address + and with new data to transfer if the direction change or manage only the new data to + transfer + if no direction change and without a final stop condition in both cases + (++) I2C_LAST_FRAME: Sequential usage, this option allow to manage a sequance with a restart condition, address + and with new data to transfer if the direction change or manage only the new data to + transfer + if no direction change and with a final stop condition in both cases + (++) I2C_LAST_FRAME_NO_STOP: Sequential usage (Master only), this option allow to manage a restart condition + after several call of the same master sequential interface several times + (link with option I2C_FIRST_AND_NEXT_FRAME). + Usage can, transfer several bytes one by one using + HAL_I2C_Master_Seq_Transmit_IT + or HAL_I2C_Master_Seq_Receive_IT + or HAL_I2C_Master_Seq_Transmit_DMA + or HAL_I2C_Master_Seq_Receive_DMA + with option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME. + Then usage of this option I2C_LAST_FRAME_NO_STOP at the last Transmit or + Receive sequence permit to call the opposite interface Receive or Transmit + without stopping the communication and so generate a restart condition. + (++) I2C_OTHER_FRAME: Sequential usage (Master only), this option allow to manage a restart condition after + each call of the same master sequential + interface. + Usage can, transfer several bytes one by one with a restart with slave address between + each bytes using + HAL_I2C_Master_Seq_Transmit_IT + or HAL_I2C_Master_Seq_Receive_IT + or HAL_I2C_Master_Seq_Transmit_DMA + or HAL_I2C_Master_Seq_Receive_DMA + with option I2C_FIRST_FRAME then I2C_OTHER_FRAME. + Then usage of this option I2C_OTHER_AND_LAST_FRAME at the last frame to help automatic + generation of STOP condition. + + (+) Different sequential I2C interfaces are listed below: + (++) Sequential transmit in master I2C mode an amount of data in non-blocking mode using + HAL_I2C_Master_Seq_Transmit_IT() or using HAL_I2C_Master_Seq_Transmit_DMA() + (+++) At transmission end of current frame transfer, HAL_I2C_MasterTxCpltCallback() is executed and + users can add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() + (++) Sequential receive in master I2C mode an amount of data in non-blocking mode using + HAL_I2C_Master_Seq_Receive_IT() or using HAL_I2C_Master_Seq_Receive_DMA() + (+++) At reception end of current frame transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() + (++) Abort a master or memory IT or DMA I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() + (+++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_AbortCpltCallback() + (++) Enable/disable the Address listen mode in slave I2C mode using HAL_I2C_EnableListen_IT() + HAL_I2C_DisableListen_IT() + (+++) When address slave I2C match, HAL_I2C_AddrCallback() is executed and users can + add their own code to check the Address Match Code and the transmission direction request by master + (Write/Read). + (+++) At Listen mode end HAL_I2C_ListenCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_ListenCpltCallback() + (++) Sequential transmit in slave I2C mode an amount of data in non-blocking mode using + HAL_I2C_Slave_Seq_Transmit_IT() or using HAL_I2C_Slave_Seq_Transmit_DMA() + (+++) At transmission end of current frame transfer, HAL_I2C_SlaveTxCpltCallback() is executed and + users can add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() + (++) Sequential receive in slave I2C mode an amount of data in non-blocking mode using + HAL_I2C_Slave_Seq_Receive_IT() or using HAL_I2C_Slave_Seq_Receive_DMA() + (+++) At reception end of current frame transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() + (++) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can + add their own code by customization of function pointer HAL_I2C_ErrorCallback() + (++) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. + This action will inform Master to generate a Stop condition to discard the communication. + + *** Interrupt mode IO MEM operation *** + ======================================= + [..] + (+) Write an amount of data in non-blocking mode with Interrupt to a specific memory address using + HAL_I2C_Mem_Write_IT() + (+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MemTxCpltCallback() + (+) Read an amount of data in non-blocking mode with Interrupt from a specific memory address using + HAL_I2C_Mem_Read_IT() + (+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MemRxCpltCallback() + (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can + add their own code by customization of function pointer HAL_I2C_ErrorCallback() + + *** DMA mode IO operation *** + ============================== + [..] + (+) Transmit in master mode an amount of data in non-blocking mode (DMA) using + HAL_I2C_Master_Transmit_DMA() + (+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback() + (+) Receive in master mode an amount of data in non-blocking mode (DMA) using + HAL_I2C_Master_Receive_DMA() + (+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback() + (+) Transmit in slave mode an amount of data in non-blocking mode (DMA) using + HAL_I2C_Slave_Transmit_DMA() + (+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback() + (+) Receive in slave mode an amount of data in non-blocking mode (DMA) using + HAL_I2C_Slave_Receive_DMA() + (+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback() + (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can + add their own code by customization of function pointer HAL_I2C_ErrorCallback() + (+) Abort a master or memory I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT() + (+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_AbortCpltCallback() + (+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro. + This action will inform Master to generate a Stop condition to discard the communication. + + *** DMA mode IO MEM operation *** + ================================= + [..] + (+) Write an amount of data in non-blocking mode with DMA to a specific memory address using + HAL_I2C_Mem_Write_DMA() + (+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MemTxCpltCallback() + (+) Read an amount of data in non-blocking mode with DMA from a specific memory address using + HAL_I2C_Mem_Read_DMA() + (+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and users can + add their own code by customization of function pointer HAL_I2C_MemRxCpltCallback() + (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can + add their own code by customization of function pointer HAL_I2C_ErrorCallback() + + + *** I2C HAL driver macros list *** + ================================== + [..] + Below the list of most used macros in I2C HAL driver. + + (+) __HAL_I2C_ENABLE: Enable the I2C peripheral + (+) __HAL_I2C_DISABLE: Disable the I2C peripheral + (+) __HAL_I2C_GENERATE_NACK: Generate a Non-Acknowledge I2C peripheral in Slave mode + (+) __HAL_I2C_GET_FLAG: Check whether the specified I2C flag is set or not + (+) __HAL_I2C_CLEAR_FLAG: Clear the specified I2C pending flag + (+) __HAL_I2C_ENABLE_IT: Enable the specified I2C interrupt + (+) __HAL_I2C_DISABLE_IT: Disable the specified I2C interrupt + + *** Callback registration *** + ============================================= + [..] + The compilation flag USE_HAL_I2C_REGISTER_CALLBACKS when set to 1 + allows the user to configure dynamically the driver callbacks. + Use Functions HAL_I2C_RegisterCallback() or HAL_I2C_RegisterAddrCallback() + to register an interrupt callback. + [..] + Function HAL_I2C_RegisterCallback() allows to register following callbacks: + (+) MasterTxCpltCallback : callback for Master transmission end of transfer. + (+) MasterRxCpltCallback : callback for Master reception end of transfer. + (+) SlaveTxCpltCallback : callback for Slave transmission end of transfer. + (+) SlaveRxCpltCallback : callback for Slave reception end of transfer. + (+) ListenCpltCallback : callback for end of listen mode. + (+) MemTxCpltCallback : callback for Memory transmission end of transfer. + (+) MemRxCpltCallback : callback for Memory reception end of transfer. + (+) ErrorCallback : callback for error detection. + (+) AbortCpltCallback : callback for abort completion process. + (+) MspInitCallback : callback for Msp Init. + (+) MspDeInitCallback : callback for Msp DeInit. + This function takes as parameters the HAL peripheral handle, the Callback ID + and a pointer to the user callback function. + [..] + For specific callback AddrCallback use dedicated register callbacks : HAL_I2C_RegisterAddrCallback(). + [..] + Use function HAL_I2C_UnRegisterCallback to reset a callback to the default + weak function. + HAL_I2C_UnRegisterCallback takes as parameters the HAL peripheral handle, + and the Callback ID. + This function allows to reset following callbacks: + (+) MasterTxCpltCallback : callback for Master transmission end of transfer. + (+) MasterRxCpltCallback : callback for Master reception end of transfer. + (+) SlaveTxCpltCallback : callback for Slave transmission end of transfer. + (+) SlaveRxCpltCallback : callback for Slave reception end of transfer. + (+) ListenCpltCallback : callback for end of listen mode. + (+) MemTxCpltCallback : callback for Memory transmission end of transfer. + (+) MemRxCpltCallback : callback for Memory reception end of transfer. + (+) ErrorCallback : callback for error detection. + (+) AbortCpltCallback : callback for abort completion process. + (+) MspInitCallback : callback for Msp Init. + (+) MspDeInitCallback : callback for Msp DeInit. + [..] + For callback AddrCallback use dedicated register callbacks : HAL_I2C_UnRegisterAddrCallback(). + [..] + By default, after the HAL_I2C_Init() and when the state is HAL_I2C_STATE_RESET + all callbacks are set to the corresponding weak functions: + examples HAL_I2C_MasterTxCpltCallback(), HAL_I2C_MasterRxCpltCallback(). + Exception done for MspInit and MspDeInit functions that are + reset to the legacy weak functions in the HAL_I2C_Init()/ HAL_I2C_DeInit() only when + these callbacks are null (not registered beforehand). + If MspInit or MspDeInit are not null, the HAL_I2C_Init()/ HAL_I2C_DeInit() + keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state. + [..] + Callbacks can be registered/unregistered in HAL_I2C_STATE_READY state only. + Exception done MspInit/MspDeInit functions that can be registered/unregistered + in HAL_I2C_STATE_READY or HAL_I2C_STATE_RESET state, + thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit. + Then, the user first registers the MspInit/MspDeInit user callbacks + using HAL_I2C_RegisterCallback() before calling HAL_I2C_DeInit() + or HAL_I2C_Init() function. + [..] + When the compilation flag USE_HAL_I2C_REGISTER_CALLBACKS is set to 0 or + not defined, the callback registration feature is not available and all callbacks + are set to the corresponding weak functions. + + [..] + (@) You can refer to the I2C HAL driver header file for more useful macros + + @endverbatim + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32h7xx_hal.h" + +/** @addtogroup STM32H7xx_HAL_Driver + * @{ + */ + +/** @defgroup I2C I2C + * @brief I2C HAL module driver + * @{ + */ + +#ifdef HAL_I2C_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ + +/** @defgroup I2C_Private_Define I2C Private Define + * @{ + */ +#define TIMING_CLEAR_MASK (0xF0FFFFFFU) /*!< I2C TIMING clear register Mask */ +#define I2C_TIMEOUT_ADDR (10000U) /*!< 10 s */ +#define I2C_TIMEOUT_BUSY (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_DIR (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_RXNE (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_STOPF (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_TC (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_TCR (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_TXIS (25U) /*!< 25 ms */ +#define I2C_TIMEOUT_FLAG (25U) /*!< 25 ms */ + +#define MAX_NBYTE_SIZE 255U +#define SLAVE_ADDR_SHIFT 7U +#define SLAVE_ADDR_MSK 0x06U + +/* Private define for @ref PreviousState usage */ +#define I2C_STATE_MSK ((uint32_t)((uint32_t)((uint32_t)HAL_I2C_STATE_BUSY_TX | \ + (uint32_t)HAL_I2C_STATE_BUSY_RX) & \ + (uint32_t)(~((uint32_t)HAL_I2C_STATE_READY)))) +/*!< Mask State define, keep only RX and TX bits */ +#define I2C_STATE_NONE ((uint32_t)(HAL_I2C_MODE_NONE)) +/*!< Default Value */ +#define I2C_STATE_MASTER_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_MASTER)) +/*!< Master Busy TX, combinaison of State LSB and Mode enum */ +#define I2C_STATE_MASTER_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_MASTER)) +/*!< Master Busy RX, combinaison of State LSB and Mode enum */ +#define I2C_STATE_SLAVE_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_SLAVE)) +/*!< Slave Busy TX, combinaison of State LSB and Mode enum */ +#define I2C_STATE_SLAVE_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_SLAVE)) +/*!< Slave Busy RX, combinaison of State LSB and Mode enum */ +#define I2C_STATE_MEM_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_MEM)) +/*!< Memory Busy TX, combinaison of State LSB and Mode enum */ +#define I2C_STATE_MEM_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \ + (uint32_t)HAL_I2C_MODE_MEM)) +/*!< Memory Busy RX, combinaison of State LSB and Mode enum */ + + +/* Private define to centralize the enable/disable of Interrupts */ +#define I2C_XFER_TX_IT (uint16_t)(0x0001U) /*!< Bit field can be combinated with + @ref I2C_XFER_LISTEN_IT */ +#define I2C_XFER_RX_IT (uint16_t)(0x0002U) /*!< Bit field can be combinated with + @ref I2C_XFER_LISTEN_IT */ +#define I2C_XFER_LISTEN_IT (uint16_t)(0x8000U) /*!< Bit field can be combinated with @ref I2C_XFER_TX_IT + and @ref I2C_XFER_RX_IT */ + +#define I2C_XFER_ERROR_IT (uint16_t)(0x0010U) /*!< Bit definition to manage addition of global Error + and NACK treatment */ +#define I2C_XFER_CPLT_IT (uint16_t)(0x0020U) /*!< Bit definition to manage only STOP evenement */ +#define I2C_XFER_RELOAD_IT (uint16_t)(0x0040U) /*!< Bit definition to manage only Reload of NBYTE */ + +/* Private define Sequential Transfer Options default/reset value */ +#define I2C_NO_OPTION_FRAME (0xFFFF0000U) +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @addtogroup I2C_Private_Macro + * @{ + */ +/* Macro to get remaining data to transfer on DMA side */ +#define I2C_GET_DMA_REMAIN_DATA(__HANDLE__) __HAL_DMA_GET_COUNTER(__HANDLE__) +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ + +/** @defgroup I2C_Private_Functions I2C Private Functions + * @{ + */ +/* Private functions to handle DMA transfer */ +static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma); +static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma); +static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma); +static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma); +static void I2C_DMAError(DMA_HandleTypeDef *hdma); +static void I2C_DMAAbort(DMA_HandleTypeDef *hdma); + + +/* Private functions to handle IT transfer */ +static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); +static void I2C_ITMasterSeqCplt(I2C_HandleTypeDef *hi2c); +static void I2C_ITSlaveSeqCplt(I2C_HandleTypeDef *hi2c); +static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); +static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); +static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags); +static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode); + +/* Private functions to handle IT transfer */ +static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, + uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, + uint32_t Tickstart); +static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, + uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, + uint32_t Tickstart); + +/* Private functions for I2C transfer IRQ handler */ +static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); +static HAL_StatusTypeDef I2C_Mem_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); +static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); +static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); +static HAL_StatusTypeDef I2C_Mem_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); +static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources); + +/* Private functions to handle flags during polling transfer */ +static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, + uint32_t Timeout, uint32_t Tickstart); +static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart); +static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart); +static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart); +static HAL_StatusTypeDef I2C_IsErrorOccurred(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart); + +/* Private functions to centralize the enable/disable of Interrupts */ +static void I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest); +static void I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest); + +/* Private function to treat different error callback */ +static void I2C_TreatErrorCallback(I2C_HandleTypeDef *hi2c); + +/* Private function to flush TXDR register */ +static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c); + +/* Private function to handle start, restart or stop a transfer */ +static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, + uint32_t Request); + +/* Private function to Convert Specific options */ +static void I2C_ConvertOtherXferOptions(I2C_HandleTypeDef *hi2c); +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup I2C_Exported_Functions I2C Exported Functions + * @{ + */ + +/** @defgroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to initialize and + deinitialize the I2Cx peripheral: + + (+) User must Implement HAL_I2C_MspInit() function in which he configures + all related peripherals resources (CLOCK, GPIO, DMA, IT and NVIC ). + + (+) Call the function HAL_I2C_Init() to configure the selected device with + the selected configuration: + (++) Clock Timing + (++) Own Address 1 + (++) Addressing mode (Master, Slave) + (++) Dual Addressing mode + (++) Own Address 2 + (++) Own Address 2 Mask + (++) General call mode + (++) Nostretch mode + + (+) Call the function HAL_I2C_DeInit() to restore the default configuration + of the selected I2Cx peripheral. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the I2C according to the specified parameters + * in the I2C_InitTypeDef and initialize the associated handle. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c) +{ + /* Check the I2C handle allocation */ + if (hi2c == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); + assert_param(IS_I2C_OWN_ADDRESS1(hi2c->Init.OwnAddress1)); + assert_param(IS_I2C_ADDRESSING_MODE(hi2c->Init.AddressingMode)); + assert_param(IS_I2C_DUAL_ADDRESS(hi2c->Init.DualAddressMode)); + assert_param(IS_I2C_OWN_ADDRESS2(hi2c->Init.OwnAddress2)); + assert_param(IS_I2C_OWN_ADDRESS2_MASK(hi2c->Init.OwnAddress2Masks)); + assert_param(IS_I2C_GENERAL_CALL(hi2c->Init.GeneralCallMode)); + assert_param(IS_I2C_NO_STRETCH(hi2c->Init.NoStretchMode)); + + if (hi2c->State == HAL_I2C_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + hi2c->Lock = HAL_UNLOCKED; + +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + /* Init the I2C Callback settings */ + hi2c->MasterTxCpltCallback = HAL_I2C_MasterTxCpltCallback; /* Legacy weak MasterTxCpltCallback */ + hi2c->MasterRxCpltCallback = HAL_I2C_MasterRxCpltCallback; /* Legacy weak MasterRxCpltCallback */ + hi2c->SlaveTxCpltCallback = HAL_I2C_SlaveTxCpltCallback; /* Legacy weak SlaveTxCpltCallback */ + hi2c->SlaveRxCpltCallback = HAL_I2C_SlaveRxCpltCallback; /* Legacy weak SlaveRxCpltCallback */ + hi2c->ListenCpltCallback = HAL_I2C_ListenCpltCallback; /* Legacy weak ListenCpltCallback */ + hi2c->MemTxCpltCallback = HAL_I2C_MemTxCpltCallback; /* Legacy weak MemTxCpltCallback */ + hi2c->MemRxCpltCallback = HAL_I2C_MemRxCpltCallback; /* Legacy weak MemRxCpltCallback */ + hi2c->ErrorCallback = HAL_I2C_ErrorCallback; /* Legacy weak ErrorCallback */ + hi2c->AbortCpltCallback = HAL_I2C_AbortCpltCallback; /* Legacy weak AbortCpltCallback */ + hi2c->AddrCallback = HAL_I2C_AddrCallback; /* Legacy weak AddrCallback */ + + if (hi2c->MspInitCallback == NULL) + { + hi2c->MspInitCallback = HAL_I2C_MspInit; /* Legacy weak MspInit */ + } + + /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */ + hi2c->MspInitCallback(hi2c); +#else + /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */ + HAL_I2C_MspInit(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the selected I2C peripheral */ + __HAL_I2C_DISABLE(hi2c); + + /*---------------------------- I2Cx TIMINGR Configuration ------------------*/ + /* Configure I2Cx: Frequency range */ + hi2c->Instance->TIMINGR = hi2c->Init.Timing & TIMING_CLEAR_MASK; + + /*---------------------------- I2Cx OAR1 Configuration ---------------------*/ + /* Disable Own Address1 before set the Own Address1 configuration */ + hi2c->Instance->OAR1 &= ~I2C_OAR1_OA1EN; + + /* Configure I2Cx: Own Address1 and ack own address1 mode */ + if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_7BIT) + { + hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN | hi2c->Init.OwnAddress1); + } + else /* I2C_ADDRESSINGMODE_10BIT */ + { + hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN | I2C_OAR1_OA1MODE | hi2c->Init.OwnAddress1); + } + + /*---------------------------- I2Cx CR2 Configuration ----------------------*/ + /* Configure I2Cx: Addressing Master mode */ + if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) + { + SET_BIT(hi2c->Instance->CR2, I2C_CR2_ADD10); + } + else + { + /* Clear the I2C ADD10 bit */ + CLEAR_BIT(hi2c->Instance->CR2, I2C_CR2_ADD10); + } + /* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process */ + hi2c->Instance->CR2 |= (I2C_CR2_AUTOEND | I2C_CR2_NACK); + + /*---------------------------- I2Cx OAR2 Configuration ---------------------*/ + /* Disable Own Address2 before set the Own Address2 configuration */ + hi2c->Instance->OAR2 &= ~I2C_DUALADDRESS_ENABLE; + + /* Configure I2Cx: Dual mode and Own Address2 */ + hi2c->Instance->OAR2 = (hi2c->Init.DualAddressMode | hi2c->Init.OwnAddress2 | \ + (hi2c->Init.OwnAddress2Masks << 8)); + + /*---------------------------- I2Cx CR1 Configuration ----------------------*/ + /* Configure I2Cx: Generalcall and NoStretch mode */ + hi2c->Instance->CR1 = (hi2c->Init.GeneralCallMode | hi2c->Init.NoStretchMode); + + /* Enable the selected I2C peripheral */ + __HAL_I2C_ENABLE(hi2c); + + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + hi2c->Mode = HAL_I2C_MODE_NONE; + + return HAL_OK; +} + +/** + * @brief DeInitialize the I2C peripheral. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c) +{ + /* Check the I2C handle allocation */ + if (hi2c == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the I2C Peripheral Clock */ + __HAL_I2C_DISABLE(hi2c); + +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + if (hi2c->MspDeInitCallback == NULL) + { + hi2c->MspDeInitCallback = HAL_I2C_MspDeInit; /* Legacy weak MspDeInit */ + } + + /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ + hi2c->MspDeInitCallback(hi2c); +#else + /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ + HAL_I2C_MspDeInit(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + hi2c->State = HAL_I2C_STATE_RESET; + hi2c->PreviousState = I2C_STATE_NONE; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Release Lock */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Initialize the I2C MSP. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MspInit could be implemented in the user file + */ +} + +/** + * @brief DeInitialize the I2C MSP. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MspDeInit could be implemented in the user file + */ +} + +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) +/** + * @brief Register a User I2C Callback + * To be used instead of the weak predefined callback + * @note The HAL_I2C_RegisterCallback() may be called before HAL_I2C_Init() in HAL_I2C_STATE_RESET + * to register callbacks for HAL_I2C_MSPINIT_CB_ID and HAL_I2C_MSPDEINIT_CB_ID. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param CallbackID ID of the callback to be registered + * This parameter can be one of the following values: + * @arg @ref HAL_I2C_MASTER_TX_COMPLETE_CB_ID Master Tx Transfer completed callback ID + * @arg @ref HAL_I2C_MASTER_RX_COMPLETE_CB_ID Master Rx Transfer completed callback ID + * @arg @ref HAL_I2C_SLAVE_TX_COMPLETE_CB_ID Slave Tx Transfer completed callback ID + * @arg @ref HAL_I2C_SLAVE_RX_COMPLETE_CB_ID Slave Rx Transfer completed callback ID + * @arg @ref HAL_I2C_LISTEN_COMPLETE_CB_ID Listen Complete callback ID + * @arg @ref HAL_I2C_MEM_TX_COMPLETE_CB_ID Memory Tx Transfer callback ID + * @arg @ref HAL_I2C_MEM_RX_COMPLETE_CB_ID Memory Rx Transfer completed callback ID + * @arg @ref HAL_I2C_ERROR_CB_ID Error callback ID + * @arg @ref HAL_I2C_ABORT_CB_ID Abort callback ID + * @arg @ref HAL_I2C_MSPINIT_CB_ID MspInit callback ID + * @arg @ref HAL_I2C_MSPDEINIT_CB_ID MspDeInit callback ID + * @param pCallback pointer to the Callback function + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_RegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID, + pI2C_CallbackTypeDef pCallback) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (pCallback == NULL) + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + return HAL_ERROR; + } + + if (HAL_I2C_STATE_READY == hi2c->State) + { + switch (CallbackID) + { + case HAL_I2C_MASTER_TX_COMPLETE_CB_ID : + hi2c->MasterTxCpltCallback = pCallback; + break; + + case HAL_I2C_MASTER_RX_COMPLETE_CB_ID : + hi2c->MasterRxCpltCallback = pCallback; + break; + + case HAL_I2C_SLAVE_TX_COMPLETE_CB_ID : + hi2c->SlaveTxCpltCallback = pCallback; + break; + + case HAL_I2C_SLAVE_RX_COMPLETE_CB_ID : + hi2c->SlaveRxCpltCallback = pCallback; + break; + + case HAL_I2C_LISTEN_COMPLETE_CB_ID : + hi2c->ListenCpltCallback = pCallback; + break; + + case HAL_I2C_MEM_TX_COMPLETE_CB_ID : + hi2c->MemTxCpltCallback = pCallback; + break; + + case HAL_I2C_MEM_RX_COMPLETE_CB_ID : + hi2c->MemRxCpltCallback = pCallback; + break; + + case HAL_I2C_ERROR_CB_ID : + hi2c->ErrorCallback = pCallback; + break; + + case HAL_I2C_ABORT_CB_ID : + hi2c->AbortCpltCallback = pCallback; + break; + + case HAL_I2C_MSPINIT_CB_ID : + hi2c->MspInitCallback = pCallback; + break; + + case HAL_I2C_MSPDEINIT_CB_ID : + hi2c->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (HAL_I2C_STATE_RESET == hi2c->State) + { + switch (CallbackID) + { + case HAL_I2C_MSPINIT_CB_ID : + hi2c->MspInitCallback = pCallback; + break; + + case HAL_I2C_MSPDEINIT_CB_ID : + hi2c->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} + +/** + * @brief Unregister an I2C Callback + * I2C callback is redirected to the weak predefined callback + * @note The HAL_I2C_UnRegisterCallback() may be called before HAL_I2C_Init() in HAL_I2C_STATE_RESET + * to un-register callbacks for HAL_I2C_MSPINIT_CB_ID and HAL_I2C_MSPDEINIT_CB_ID. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param CallbackID ID of the callback to be unregistered + * This parameter can be one of the following values: + * This parameter can be one of the following values: + * @arg @ref HAL_I2C_MASTER_TX_COMPLETE_CB_ID Master Tx Transfer completed callback ID + * @arg @ref HAL_I2C_MASTER_RX_COMPLETE_CB_ID Master Rx Transfer completed callback ID + * @arg @ref HAL_I2C_SLAVE_TX_COMPLETE_CB_ID Slave Tx Transfer completed callback ID + * @arg @ref HAL_I2C_SLAVE_RX_COMPLETE_CB_ID Slave Rx Transfer completed callback ID + * @arg @ref HAL_I2C_LISTEN_COMPLETE_CB_ID Listen Complete callback ID + * @arg @ref HAL_I2C_MEM_TX_COMPLETE_CB_ID Memory Tx Transfer callback ID + * @arg @ref HAL_I2C_MEM_RX_COMPLETE_CB_ID Memory Rx Transfer completed callback ID + * @arg @ref HAL_I2C_ERROR_CB_ID Error callback ID + * @arg @ref HAL_I2C_ABORT_CB_ID Abort callback ID + * @arg @ref HAL_I2C_MSPINIT_CB_ID MspInit callback ID + * @arg @ref HAL_I2C_MSPDEINIT_CB_ID MspDeInit callback ID + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_UnRegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (HAL_I2C_STATE_READY == hi2c->State) + { + switch (CallbackID) + { + case HAL_I2C_MASTER_TX_COMPLETE_CB_ID : + hi2c->MasterTxCpltCallback = HAL_I2C_MasterTxCpltCallback; /* Legacy weak MasterTxCpltCallback */ + break; + + case HAL_I2C_MASTER_RX_COMPLETE_CB_ID : + hi2c->MasterRxCpltCallback = HAL_I2C_MasterRxCpltCallback; /* Legacy weak MasterRxCpltCallback */ + break; + + case HAL_I2C_SLAVE_TX_COMPLETE_CB_ID : + hi2c->SlaveTxCpltCallback = HAL_I2C_SlaveTxCpltCallback; /* Legacy weak SlaveTxCpltCallback */ + break; + + case HAL_I2C_SLAVE_RX_COMPLETE_CB_ID : + hi2c->SlaveRxCpltCallback = HAL_I2C_SlaveRxCpltCallback; /* Legacy weak SlaveRxCpltCallback */ + break; + + case HAL_I2C_LISTEN_COMPLETE_CB_ID : + hi2c->ListenCpltCallback = HAL_I2C_ListenCpltCallback; /* Legacy weak ListenCpltCallback */ + break; + + case HAL_I2C_MEM_TX_COMPLETE_CB_ID : + hi2c->MemTxCpltCallback = HAL_I2C_MemTxCpltCallback; /* Legacy weak MemTxCpltCallback */ + break; + + case HAL_I2C_MEM_RX_COMPLETE_CB_ID : + hi2c->MemRxCpltCallback = HAL_I2C_MemRxCpltCallback; /* Legacy weak MemRxCpltCallback */ + break; + + case HAL_I2C_ERROR_CB_ID : + hi2c->ErrorCallback = HAL_I2C_ErrorCallback; /* Legacy weak ErrorCallback */ + break; + + case HAL_I2C_ABORT_CB_ID : + hi2c->AbortCpltCallback = HAL_I2C_AbortCpltCallback; /* Legacy weak AbortCpltCallback */ + break; + + case HAL_I2C_MSPINIT_CB_ID : + hi2c->MspInitCallback = HAL_I2C_MspInit; /* Legacy weak MspInit */ + break; + + case HAL_I2C_MSPDEINIT_CB_ID : + hi2c->MspDeInitCallback = HAL_I2C_MspDeInit; /* Legacy weak MspDeInit */ + break; + + default : + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (HAL_I2C_STATE_RESET == hi2c->State) + { + switch (CallbackID) + { + case HAL_I2C_MSPINIT_CB_ID : + hi2c->MspInitCallback = HAL_I2C_MspInit; /* Legacy weak MspInit */ + break; + + case HAL_I2C_MSPDEINIT_CB_ID : + hi2c->MspDeInitCallback = HAL_I2C_MspDeInit; /* Legacy weak MspDeInit */ + break; + + default : + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} + +/** + * @brief Register the Slave Address Match I2C Callback + * To be used instead of the weak HAL_I2C_AddrCallback() predefined callback + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pCallback pointer to the Address Match Callback function + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_RegisterAddrCallback(I2C_HandleTypeDef *hi2c, pI2C_AddrCallbackTypeDef pCallback) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (pCallback == NULL) + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + return HAL_ERROR; + } + + if (HAL_I2C_STATE_READY == hi2c->State) + { + hi2c->AddrCallback = pCallback; + } + else + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} + +/** + * @brief UnRegister the Slave Address Match I2C Callback + * Info Ready I2C Callback is redirected to the weak HAL_I2C_AddrCallback() predefined callback + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_UnRegisterAddrCallback(I2C_HandleTypeDef *hi2c) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (HAL_I2C_STATE_READY == hi2c->State) + { + hi2c->AddrCallback = HAL_I2C_AddrCallback; /* Legacy weak AddrCallback */ + } + else + { + /* Update the error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} + +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/** @defgroup I2C_Exported_Functions_Group2 Input and Output operation functions + * @brief Data transfers functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to manage the I2C data + transfers. + + (#) There are two modes of transfer: + (++) Blocking mode : The communication is performed in the polling mode. + The status of all data processing is returned by the same function + after finishing transfer. + (++) No-Blocking mode : The communication is performed using Interrupts + or DMA. These functions return the status of the transfer startup. + The end of the data processing will be indicated through the + dedicated I2C IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + + (#) Blocking mode functions are : + (++) HAL_I2C_Master_Transmit() + (++) HAL_I2C_Master_Receive() + (++) HAL_I2C_Slave_Transmit() + (++) HAL_I2C_Slave_Receive() + (++) HAL_I2C_Mem_Write() + (++) HAL_I2C_Mem_Read() + (++) HAL_I2C_IsDeviceReady() + + (#) No-Blocking mode functions with Interrupt are : + (++) HAL_I2C_Master_Transmit_IT() + (++) HAL_I2C_Master_Receive_IT() + (++) HAL_I2C_Slave_Transmit_IT() + (++) HAL_I2C_Slave_Receive_IT() + (++) HAL_I2C_Mem_Write_IT() + (++) HAL_I2C_Mem_Read_IT() + (++) HAL_I2C_Master_Seq_Transmit_IT() + (++) HAL_I2C_Master_Seq_Receive_IT() + (++) HAL_I2C_Slave_Seq_Transmit_IT() + (++) HAL_I2C_Slave_Seq_Receive_IT() + (++) HAL_I2C_EnableListen_IT() + (++) HAL_I2C_DisableListen_IT() + (++) HAL_I2C_Master_Abort_IT() + + (#) No-Blocking mode functions with DMA are : + (++) HAL_I2C_Master_Transmit_DMA() + (++) HAL_I2C_Master_Receive_DMA() + (++) HAL_I2C_Slave_Transmit_DMA() + (++) HAL_I2C_Slave_Receive_DMA() + (++) HAL_I2C_Mem_Write_DMA() + (++) HAL_I2C_Mem_Read_DMA() + (++) HAL_I2C_Master_Seq_Transmit_DMA() + (++) HAL_I2C_Master_Seq_Receive_DMA() + (++) HAL_I2C_Slave_Seq_Transmit_DMA() + (++) HAL_I2C_Slave_Seq_Receive_DMA() + + (#) A set of Transfer Complete Callbacks are provided in non Blocking mode: + (++) HAL_I2C_MasterTxCpltCallback() + (++) HAL_I2C_MasterRxCpltCallback() + (++) HAL_I2C_SlaveTxCpltCallback() + (++) HAL_I2C_SlaveRxCpltCallback() + (++) HAL_I2C_MemTxCpltCallback() + (++) HAL_I2C_MemRxCpltCallback() + (++) HAL_I2C_AddrCallback() + (++) HAL_I2C_ListenCpltCallback() + (++) HAL_I2C_ErrorCallback() + (++) HAL_I2C_AbortCpltCallback() + +@endverbatim + * @{ + */ + +/** + * @brief Transmits in master mode an amount of data in blocking mode. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t Timeout) +{ + uint32_t tickstart; + uint32_t xfermode; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferISR = NULL; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = I2C_AUTOEND_MODE; + } + + if (hi2c->XferSize > 0U) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)(hi2c->XferSize + 1U), xfermode, + I2C_GENERATE_START_WRITE); + } + else + { + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, + I2C_GENERATE_START_WRITE); + } + + while (hi2c->XferCount > 0U) + { + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + /* Wait until TCR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, + I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_NO_STARTSTOP); + } + } + } + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is set */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives in master mode an amount of data in blocking mode. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t Timeout) +{ + uint32_t tickstart; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferISR = NULL; + + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, + I2C_GENERATE_START_READ); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_GENERATE_START_READ); + } + + while (hi2c->XferCount > 0U) + { + /* Wait until RXNE flag is set */ + if (I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + /* Wait until TCR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, + I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_NO_STARTSTOP); + } + } + } + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is set */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmits in slave mode an amount of data in blocking mode. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t Timeout) +{ + uint32_t tickstart; + uint16_t tmpXferCount; + HAL_StatusTypeDef error; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferISR = NULL; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Preload TX data if no stretch enable */ + if (hi2c->Init.NoStretchMode == I2C_NOSTRETCH_ENABLE) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + } + + /* Wait until ADDR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + return HAL_ERROR; + } + + /* Clear ADDR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + + /* If 10bit addressing mode is selected */ + if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) + { + /* Wait until ADDR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + return HAL_ERROR; + } + + /* Clear ADDR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + } + + /* Wait until DIR flag is set Transmitter mode */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, RESET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + return HAL_ERROR; + } + + while (hi2c->XferCount > 0U) + { + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + } + + /* Wait until AF flag is set */ + error = I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_AF, RESET, Timeout, tickstart); + + if (error != HAL_OK) + { + /* Check that I2C transfer finished */ + /* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ + /* Mean XferCount == 0 */ + + tmpXferCount = hi2c->XferCount; + if ((hi2c->ErrorCode == HAL_I2C_ERROR_AF) && (tmpXferCount == 0U)) + { + /* Reset ErrorCode to NONE */ + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + } + else + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + } + else + { + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Clear AF flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Wait until STOP flag is set */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + return HAL_ERROR; + } + + /* Clear STOP flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + } + + /* Wait until BUSY flag is reset */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in slave mode an amount of data in blocking mode + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t Timeout) +{ + uint32_t tickstart; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferISR = NULL; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Wait until ADDR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + /* Clear ADDR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + + /* Wait until DIR flag is reset Receiver mode */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, SET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + while (hi2c->XferCount > 0U) + { + /* Wait until RXNE flag is set */ + if (I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Store Last receive data if any */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == SET) + { + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + } + + return HAL_ERROR; + } + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + } + + /* Wait until STOP flag is set */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + /* Clear STOP flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Wait until BUSY flag is reset */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK) + { + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + return HAL_ERROR; + } + + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmit in master mode an amount of data in non-blocking mode with Interrupt + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size) +{ + uint32_t xfermode; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Master_ISR_IT; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = I2C_AUTOEND_MODE; + } + + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ + if (hi2c->XferSize > 0U) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)(hi2c->XferSize + 1U), xfermode, + I2C_GENERATE_START_WRITE); + } + else + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, + I2C_GENERATE_START_WRITE); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in master mode an amount of data in non-blocking mode with Interrupt + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size) +{ + uint32_t xfermode; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Master_ISR_IT; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = I2C_AUTOEND_MODE; + } + + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, RXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmit in slave mode an amount of data in non-blocking mode with Interrupt + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) +{ + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Slave_ISR_IT; + + /* Preload TX data if no stretch enable */ + if (hi2c->Init.NoStretchMode == I2C_NOSTRETCH_ENABLE) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT | I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in slave mode an amount of data in non-blocking mode with Interrupt + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) +{ + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Slave_ISR_IT; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, RXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmit in master mode an amount of data in non-blocking mode with DMA + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size) +{ + uint32_t xfermode; + HAL_StatusTypeDef dmaxferstatus; + uint32_t sizetoxfer = 0U; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Master_ISR_DMA; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = I2C_AUTOEND_MODE; + } + + if (hi2c->XferSize > 0U) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + sizetoxfer = hi2c->XferSize; + hi2c->XferCount--; + hi2c->XferSize--; + } + + if (hi2c->XferSize > 0U) + { + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt; + + /* Set the DMA error callback */ + hi2c->hdmatx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmatx->XferHalfCpltCallback = NULL; + hi2c->hdmatx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, + (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)(hi2c->XferSize + 1U), + xfermode, I2C_GENERATE_START_WRITE); + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR and NACK interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + else + { + /* Update Transfer ISR function pointer */ + hi2c->XferISR = I2C_Master_ISR_IT; + + /* Send Slave Address */ + /* Set NBYTES to write and generate START condition */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)sizetoxfer, I2C_AUTOEND_MODE, + I2C_GENERATE_START_WRITE); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in master mode an amount of data in non-blocking mode with DMA + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size) +{ + uint32_t xfermode; + HAL_StatusTypeDef dmaxferstatus; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Master_ISR_DMA; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = I2C_AUTOEND_MODE; + } + + if (hi2c->XferSize > 0U) + { + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt; + + /* Set the DMA error callback */ + hi2c->hdmarx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmarx->XferHalfCpltCallback = NULL; + hi2c->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address */ + /* Set NBYTES to read and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, I2C_GENERATE_START_READ); + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR and NACK interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + else + { + /* Update Transfer ISR function pointer */ + hi2c->XferISR = I2C_Master_ISR_IT; + + /* Send Slave Address */ + /* Set NBYTES to read and generate START condition */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_GENERATE_START_READ); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, RXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmit in slave mode an amount of data in non-blocking mode with DMA + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef dmaxferstatus; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Slave_ISR_DMA; + + /* Preload TX data if no stretch enable */ + if (hi2c->Init.NoStretchMode == I2C_NOSTRETCH_ENABLE) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + } + + if (hi2c->XferCount != 0U) + { + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmatx->XferCpltCallback = I2C_DMASlaveTransmitCplt; + + /* Set the DMA error callback */ + hi2c->hdmatx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmatx->XferHalfCpltCallback = NULL; + hi2c->hdmatx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, + (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, STOP, NACK, ADDR interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + else + { + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, STOP, NACK, ADDR interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in slave mode an amount of data in non-blocking mode with DMA + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef dmaxferstatus; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Slave_ISR_DMA; + + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmarx->XferCpltCallback = I2C_DMASlaveReceiveCplt; + + /* Set the DMA error callback */ + hi2c->hdmarx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmarx->XferHalfCpltCallback = NULL; + hi2c->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, STOP, NACK, ADDR interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Write an amount of data in blocking mode to a specific memory address + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferISR = NULL; + + /* Send Slave Address and Memory Address */ + if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + return HAL_ERROR; + } + + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); + } + + do + { + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + /* Wait until TCR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, + I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_NO_STARTSTOP); + } + } + + } while (hi2c->XferCount > 0U); + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is reset */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Read an amount of data in blocking mode from a specific memory address + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Init tickstart for timeout management*/ + tickstart = HAL_GetTick(); + + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferISR = NULL; + + /* Send Slave Address and Memory Address */ + if (I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + return HAL_ERROR; + } + + /* Send Slave Address */ + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, + I2C_GENERATE_START_READ); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_GENERATE_START_READ); + } + + do + { + /* Wait until RXNE flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_RXNE, RESET, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + /* Wait until TCR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t) hi2c->XferSize, I2C_RELOAD_MODE, + I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_NO_STARTSTOP); + } + } + } while (hi2c->XferCount > 0U); + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is reset */ + if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} +/** + * @brief Write an amount of data in non-blocking mode with Interrupt to a specific memory address + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size) +{ + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->XferSize = 0U; + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Mem_ISR_IT; + hi2c->Devaddress = DevAddress; + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Prefetch Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + /* If Memory address size is 16Bit */ + else + { + /* Prefetch Memory Address (MSB part, LSB will be manage through interrupt) */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Prepare Memaddress buffer for LSB part */ + hi2c->Memaddress = I2C_MEM_ADD_LSB(MemAddress); + } + /* Send Slave Address and Memory Address */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Read an amount of data in non-blocking mode with Interrupt from a specific memory address + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size) +{ + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Mem_ISR_IT; + hi2c->Devaddress = DevAddress; + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Prefetch Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + /* If Memory address size is 16Bit */ + else + { + /* Prefetch Memory Address (MSB part, LSB will be manage through interrupt) */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Prepare Memaddress buffer for LSB part */ + hi2c->Memaddress = I2C_MEM_ADD_LSB(MemAddress); + } + /* Send Slave Address and Memory Address */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Write an amount of data in non-blocking mode with DMA to a specific memory address + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef dmaxferstatus; + + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Mem_ISR_DMA; + hi2c->Devaddress = DevAddress; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + } + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Prefetch Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + /* If Memory address size is 16Bit */ + else + { + /* Prefetch Memory Address (MSB part, LSB will be manage through interrupt) */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Prepare Memaddress buffer for LSB part */ + hi2c->Memaddress = I2C_MEM_ADD_LSB(MemAddress); + } + + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt; + + /* Set the DMA error callback */ + hi2c->hdmatx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmatx->XferHalfCpltCallback = NULL; + hi2c->hdmatx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address and Memory Address */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Reads an amount of data in non-blocking mode with DMA from a specific memory address. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param pData Pointer to data buffer + * @param Size Amount of data to be read + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, + uint16_t MemAddSize, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef dmaxferstatus; + + /* Check the parameters */ + assert_param(IS_I2C_MEMADD_SIZE(MemAddSize)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MEM; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferISR = I2C_Mem_ISR_DMA; + hi2c->Devaddress = DevAddress; + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + } + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Prefetch Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + /* If Memory address size is 16Bit */ + else + { + /* Prefetch Memory Address (MSB part, LSB will be manage through interrupt) */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Prepare Memaddress buffer for LSB part */ + hi2c->Memaddress = I2C_MEM_ADD_LSB(MemAddress); + } + + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt; + + /* Set the DMA error callback */ + hi2c->hdmarx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmarx->XferHalfCpltCallback = NULL; + hi2c->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address and Memory Address */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Checks if target device is ready for communication. + * @note This function is used with Memory devices + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param Trials Number of trials + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials, + uint32_t Timeout) +{ + uint32_t tickstart; + + __IO uint32_t I2C_Trials = 0UL; + + HAL_StatusTypeDef status = HAL_OK; + + FlagStatus tmp1; + FlagStatus tmp2; + + if (hi2c->State == HAL_I2C_STATE_READY) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + do + { + /* Generate Start */ + hi2c->Instance->CR2 = I2C_GENERATE_START(hi2c->Init.AddressingMode, DevAddress); + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is set or a NACK flag is set*/ + tickstart = HAL_GetTick(); + + tmp1 = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF); + tmp2 = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF); + + while ((tmp1 == RESET) && (tmp2 == RESET)) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + + tmp1 = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF); + tmp2 = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF); + } + + /* Check if the NACKF flag has not been set */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == RESET) + { + /* Wait until STOPF flag is reset */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK) + { + /* A non acknowledge appear during STOP Flag waiting process, a new trial must be performed */ + if (hi2c->ErrorCode == HAL_I2C_ERROR_AF) + { + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Reset the error code for next trial */ + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + } + else + { + status = HAL_ERROR; + } + } + else + { + /* A acknowledge appear during STOP Flag waiting process, this mean that device respond to its address */ + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Device is ready */ + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + } + else + { + /* A non acknowledge is detected, this mean that device not respond to its address, + a new trial must be performed */ + + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Wait until STOPF flag is reset */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK) + { + status = HAL_ERROR; + } + else + { + /* Clear STOP Flag, auto generated with autoend*/ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + } + } + + /* Increment Trials */ + I2C_Trials++; + + if ((I2C_Trials < Trials) && (status == HAL_ERROR)) + { + status = HAL_OK; + } + + } while (I2C_Trials < Trials); + + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sequential transmit in master I2C mode an amount of data in non-blocking mode with Interrupt. + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t XferOptions) +{ + uint32_t xfermode; + uint32_t xferrequest = I2C_GENERATE_START_WRITE; + uint32_t sizetoxfer = 0U; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Master_ISR_IT; + + /* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = hi2c->XferOptions; + } + + if ((hi2c->XferSize > 0U) && ((XferOptions == I2C_FIRST_FRAME) || \ + (XferOptions == I2C_FIRST_AND_LAST_FRAME))) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + sizetoxfer = hi2c->XferSize; + hi2c->XferCount--; + hi2c->XferSize--; + } + + /* If transfer direction not change and there is no request to start another frame, + do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && \ + (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0)) + { + xferrequest = I2C_NO_STARTSTOP; + } + else + { + /* Convert OTHER_xxx XferOptions if any */ + I2C_ConvertOtherXferOptions(hi2c); + + /* Update xfermode accordingly if no reload is necessary */ + if (hi2c->XferCount <= MAX_NBYTE_SIZE) + { + xfermode = hi2c->XferOptions; + } + } + + /* Send Slave Address and set NBYTES to write */ + if ((XferOptions == I2C_FIRST_FRAME) || (XferOptions == I2C_FIRST_AND_LAST_FRAME)) + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)sizetoxfer, xfermode, xferrequest); + } + else + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, xferrequest); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sequential transmit in master I2C mode an amount of data in non-blocking mode with DMA. + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t XferOptions) +{ + uint32_t xfermode; + uint32_t xferrequest = I2C_GENERATE_START_WRITE; + HAL_StatusTypeDef dmaxferstatus; + uint32_t sizetoxfer = 0U; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_TX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Master_ISR_DMA; + + /* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = hi2c->XferOptions; + } + + if ((hi2c->XferSize > 0U) && ((XferOptions == I2C_FIRST_FRAME) || \ + (XferOptions == I2C_FIRST_AND_LAST_FRAME))) + { + /* Preload TX register */ + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + sizetoxfer = hi2c->XferSize; + hi2c->XferCount--; + hi2c->XferSize--; + } + + /* If transfer direction not change and there is no request to start another frame, + do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && \ + (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0)) + { + xferrequest = I2C_NO_STARTSTOP; + } + else + { + /* Convert OTHER_xxx XferOptions if any */ + I2C_ConvertOtherXferOptions(hi2c); + + /* Update xfermode accordingly if no reload is necessary */ + if (hi2c->XferCount <= MAX_NBYTE_SIZE) + { + xfermode = hi2c->XferOptions; + } + } + + if (hi2c->XferSize > 0U) + { + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt; + + /* Set the DMA error callback */ + hi2c->hdmatx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmatx->XferHalfCpltCallback = NULL; + hi2c->hdmatx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, + (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address and set NBYTES to write */ + if ((XferOptions == I2C_FIRST_FRAME) || (XferOptions == I2C_FIRST_AND_LAST_FRAME)) + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)sizetoxfer, xfermode, xferrequest); + } + else + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, xferrequest); + } + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR and NACK interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + else + { + /* Update Transfer ISR function pointer */ + hi2c->XferISR = I2C_Master_ISR_IT; + + /* Send Slave Address */ + /* Set NBYTES to write and generate START condition */ + if ((XferOptions == I2C_FIRST_FRAME) || (XferOptions == I2C_FIRST_AND_LAST_FRAME)) + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)sizetoxfer, xfermode, xferrequest); + } + else + { + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, xferrequest); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sequential receive in master I2C mode an amount of data in non-blocking mode with Interrupt + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t XferOptions) +{ + uint32_t xfermode; + uint32_t xferrequest = I2C_GENERATE_START_READ; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Master_ISR_IT; + + /* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = hi2c->XferOptions; + } + + /* If transfer direction not change and there is no request to start another frame, + do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && \ + (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0)) + { + xferrequest = I2C_NO_STARTSTOP; + } + else + { + /* Convert OTHER_xxx XferOptions if any */ + I2C_ConvertOtherXferOptions(hi2c); + + /* Update xfermode accordingly if no reload is necessary */ + if (hi2c->XferCount <= MAX_NBYTE_SIZE) + { + xfermode = hi2c->XferOptions; + } + } + + /* Send Slave Address and set NBYTES to read */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, xferrequest); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sequential receive in master I2C mode an amount of data in non-blocking mode with DMA + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, + uint16_t Size, uint32_t XferOptions) +{ + uint32_t xfermode; + uint32_t xferrequest = I2C_GENERATE_START_READ; + HAL_StatusTypeDef dmaxferstatus; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY_RX; + hi2c->Mode = HAL_I2C_MODE_MASTER; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Master_ISR_DMA; + + /* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + xfermode = hi2c->XferOptions; + } + + /* If transfer direction not change and there is no request to start another frame, + do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && \ + (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0)) + { + xferrequest = I2C_NO_STARTSTOP; + } + else + { + /* Convert OTHER_xxx XferOptions if any */ + I2C_ConvertOtherXferOptions(hi2c); + + /* Update xfermode accordingly if no reload is necessary */ + if (hi2c->XferCount <= MAX_NBYTE_SIZE) + { + xfermode = hi2c->XferOptions; + } + } + + if (hi2c->XferSize > 0U) + { + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt; + + /* Set the DMA error callback */ + hi2c->hdmarx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmarx->XferHalfCpltCallback = NULL; + hi2c->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Send Slave Address and set NBYTES to read */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, xfermode, xferrequest); + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR and NACK interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + else + { + /* Update Transfer ISR function pointer */ + hi2c->XferISR = I2C_Master_ISR_IT; + + /* Send Slave Address */ + /* Set NBYTES to read and generate START condition */ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, + I2C_GENERATE_START_READ); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, TC, STOP, NACK, RXI interrupt */ + /* possible to enable all of these */ + /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | + I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sequential transmit in slave/device I2C mode an amount of data in non-blocking mode with Interrupt + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t XferOptions) +{ + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + FlagStatus tmp; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) == (uint32_t)HAL_I2C_STATE_LISTEN) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT); + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* I2C cannot manage full duplex exchange so disable previous IT enabled if any */ + /* and then toggle the HAL slave RX state to TX state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN) + { + /* Disable associated Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + + /* Abort DMA Xfer if any */ + if ((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx); + } + } + } + } + + hi2c->State = HAL_I2C_STATE_BUSY_TX_LISTEN; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Slave_ISR_IT; + + tmp = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_ADDR); + if ((I2C_GET_DIR(hi2c) == I2C_DIRECTION_RECEIVE) && (tmp != RESET)) + { + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the Master */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* REnable ADDR interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT | I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Sequential transmit in slave/device I2C mode an amount of data in non-blocking mode with DMA + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t XferOptions) +{ + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + FlagStatus tmp; + HAL_StatusTypeDef dmaxferstatus; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) == (uint32_t)HAL_I2C_STATE_LISTEN) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT); + + /* I2C cannot manage full duplex exchange so disable previous IT enabled if any */ + /* and then toggle the HAL slave RX state to TX state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN) + { + /* Disable associated Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + + if ((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN) + { + /* Abort DMA Xfer if any */ + if (hi2c->hdmarx != NULL) + { + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx); + } + } + } + } + else if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) + { + if ((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + /* Abort DMA Xfer if any */ + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx); + } + } + } + } + else + { + /* Nothing to do */ + } + + hi2c->State = HAL_I2C_STATE_BUSY_TX_LISTEN; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Slave_ISR_DMA; + + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmatx->XferCpltCallback = I2C_DMASlaveTransmitCplt; + + /* Set the DMA error callback */ + hi2c->hdmatx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmatx->XferHalfCpltCallback = NULL; + hi2c->hdmatx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, + hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Reset XferSize */ + hi2c->XferSize = 0; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + tmp = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_ADDR); + if ((I2C_GET_DIR(hi2c) == I2C_DIRECTION_RECEIVE) && (tmp != RESET)) + { + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the Master */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* Enable ERR, STOP, NACK, ADDR interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Sequential receive in slave/device I2C mode an amount of data in non-blocking mode with Interrupt + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t XferOptions) +{ + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + FlagStatus tmp; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) == (uint32_t)HAL_I2C_STATE_LISTEN) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT); + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* I2C cannot manage full duplex exchange so disable previous IT enabled if any */ + /* and then toggle the HAL slave TX state to RX state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) + { + /* Disable associated Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + if ((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + /* Abort DMA Xfer if any */ + if (hi2c->hdmatx != NULL) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx); + } + } + } + } + + hi2c->State = HAL_I2C_STATE_BUSY_RX_LISTEN; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Slave_ISR_IT; + + tmp = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_ADDR); + if ((I2C_GET_DIR(hi2c) == I2C_DIRECTION_TRANSMIT) && (tmp != RESET)) + { + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the Master */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* REnable ADDR interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Sequential receive in slave/device I2C mode an amount of data in non-blocking mode with DMA + * @note This interface allow to manage repeated start condition when a direction change during transfer + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param pData Pointer to data buffer + * @param Size Amount of data to be sent + * @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, + uint32_t XferOptions) +{ + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + FlagStatus tmp; + HAL_StatusTypeDef dmaxferstatus; + + /* Check the parameters */ + assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) == (uint32_t)HAL_I2C_STATE_LISTEN) + { + if ((pData == NULL) || (Size == 0U)) + { + hi2c->ErrorCode = HAL_I2C_ERROR_INVALID_PARAM; + return HAL_ERROR; + } + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT); + + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* I2C cannot manage full duplex exchange so disable previous IT enabled if any */ + /* and then toggle the HAL slave TX state to RX state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) + { + /* Disable associated Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + if ((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) + { + /* Abort DMA Xfer if any */ + if (hi2c->hdmatx != NULL) + { + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx); + } + } + } + } + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN) + { + if ((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + /* Abort DMA Xfer if any */ + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort; + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx); + } + } + } + } + else + { + /* Nothing to do */ + } + + hi2c->State = HAL_I2C_STATE_BUSY_RX_LISTEN; + hi2c->Mode = HAL_I2C_MODE_SLAVE; + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + + /* Enable Address Acknowledge */ + hi2c->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hi2c->pBuffPtr = pData; + hi2c->XferCount = Size; + hi2c->XferSize = hi2c->XferCount; + hi2c->XferOptions = XferOptions; + hi2c->XferISR = I2C_Slave_ISR_DMA; + + if (hi2c->hdmarx != NULL) + { + /* Set the I2C DMA transfer complete callback */ + hi2c->hdmarx->XferCpltCallback = I2C_DMASlaveReceiveCplt; + + /* Set the DMA error callback */ + hi2c->hdmarx->XferErrorCallback = I2C_DMAError; + + /* Set the unused DMA callbacks to NULL */ + hi2c->hdmarx->XferHalfCpltCallback = NULL; + hi2c->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream or channel depends on Instance */ + dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, + (uint32_t)pData, hi2c->XferSize); + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA_PARAM; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + if (dmaxferstatus == HAL_OK) + { + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Reset XferSize */ + hi2c->XferSize = 0; + } + else + { + /* Update I2C state */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Update I2C error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_DMA; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + + tmp = __HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_ADDR); + if ((I2C_GET_DIR(hi2c) == I2C_DIRECTION_TRANSMIT) && (tmp != RESET)) + { + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the Master */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Enable DMA Request */ + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + /* REnable ADDR interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Enable the Address listen mode with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c) +{ + if (hi2c->State == HAL_I2C_STATE_READY) + { + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->XferISR = I2C_Slave_ISR_IT; + + /* Enable the Address Match interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Disable the Address listen mode with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c) +{ + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + uint32_t tmp; + + /* Disable Address listen mode only if a transfer is not ongoing */ + if (hi2c->State == HAL_I2C_STATE_LISTEN) + { + tmp = (uint32_t)(hi2c->State) & I2C_STATE_MSK; + hi2c->PreviousState = tmp | (uint32_t)(hi2c->Mode); + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + hi2c->XferISR = NULL; + + /* Disable the Address Match interrupt */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Abort a master or memory I2C IT or DMA process communication with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress) +{ + HAL_I2C_ModeTypeDef tmp_mode = hi2c->Mode; + + if ((tmp_mode == HAL_I2C_MODE_MASTER) || (tmp_mode == HAL_I2C_MODE_MEM)) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + /* Disable Interrupts and Store Previous state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_TX) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_TX; + } + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_RX; + } + else + { + /* Do nothing */ + } + + /* Set State at HAL_I2C_STATE_ABORT */ + hi2c->State = HAL_I2C_STATE_ABORT; + + /* Set NBYTES to 1 to generate a dummy read on I2C peripheral */ + /* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */ + I2C_TransferConfig(hi2c, DevAddress, 1, I2C_AUTOEND_MODE, I2C_GENERATE_STOP); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Note : The I2C interrupts must be enabled after unlocking current process + to avoid the risk of I2C interrupt handle execution before current + process unlock */ + I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); + + return HAL_OK; + } + else + { + /* Wrong usage of abort function */ + /* This function should be used only in case of abort monitored by master device */ + return HAL_ERROR; + } +} + +/** + * @} + */ + +/** @defgroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks + * @{ + */ + +/** + * @brief This function handles I2C event interrupt request. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c) /* Derogation MISRAC2012-Rule-8.13 */ +{ + /* Get current IT Flags and IT sources value */ + uint32_t itflags = READ_REG(hi2c->Instance->ISR); + uint32_t itsources = READ_REG(hi2c->Instance->CR1); + + /* I2C events treatment -------------------------------------*/ + if (hi2c->XferISR != NULL) + { + hi2c->XferISR(hi2c, itflags, itsources); + } +} + +/** + * @brief This function handles I2C error interrupt request. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c) +{ + uint32_t itflags = READ_REG(hi2c->Instance->ISR); + uint32_t itsources = READ_REG(hi2c->Instance->CR1); + uint32_t tmperror; + + /* I2C Bus error interrupt occurred ------------------------------------*/ + if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_BERR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_BERR; + + /* Clear BERR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_BERR); + } + + /* I2C Over-Run/Under-Run interrupt occurred ----------------------------------------*/ + if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_OVR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_OVR; + + /* Clear OVR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_OVR); + } + + /* I2C Arbitration Loss error interrupt occurred -------------------------------------*/ + if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_ARLO) != RESET) && \ + (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_ARLO; + + /* Clear ARLO flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ARLO); + } + + /* Store current volatile hi2c->ErrorCode, misra rule */ + tmperror = hi2c->ErrorCode; + + /* Call the Error Callback in case of Error detected */ + if ((tmperror & (HAL_I2C_ERROR_BERR | HAL_I2C_ERROR_OVR | HAL_I2C_ERROR_ARLO)) != HAL_I2C_ERROR_NONE) + { + I2C_ITError(hi2c, tmperror); + } +} + +/** + * @brief Master Tx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MasterTxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Master Rx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MasterRxCpltCallback could be implemented in the user file + */ +} + +/** @brief Slave Tx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_SlaveTxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Slave Rx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_SlaveRxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Slave Address Match callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param TransferDirection Master request Transfer Direction (Write/Read), value of @ref I2C_XFERDIRECTION + * @param AddrMatchCode Address Match Code + * @retval None + */ +__weak void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + UNUSED(TransferDirection); + UNUSED(AddrMatchCode); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_AddrCallback() could be implemented in the user file + */ +} + +/** + * @brief Listen Complete callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_ListenCpltCallback() could be implemented in the user file + */ +} + +/** + * @brief Memory Tx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MemTxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Memory Rx Transfer completed callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_MemRxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief I2C error callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_ErrorCallback could be implemented in the user file + */ +} + +/** + * @brief I2C abort callback. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval None + */ +__weak void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hi2c); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_I2C_AbortCpltCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions + * @brief Peripheral State, Mode and Error functions + * +@verbatim + =============================================================================== + ##### Peripheral State, Mode and Error functions ##### + =============================================================================== + [..] + This subsection permit to get in run-time the status of the peripheral + and the data flow. + +@endverbatim + * @{ + */ + +/** + * @brief Return the I2C handle state. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval HAL state + */ +HAL_I2C_StateTypeDef HAL_I2C_GetState(const I2C_HandleTypeDef *hi2c) +{ + /* Return I2C handle state */ + return hi2c->State; +} + +/** + * @brief Returns the I2C Master, Slave, Memory or no mode. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for I2C module + * @retval HAL mode + */ +HAL_I2C_ModeTypeDef HAL_I2C_GetMode(const I2C_HandleTypeDef *hi2c) +{ + return hi2c->Mode; +} + +/** + * @brief Return the I2C error code. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @retval I2C Error Code + */ +uint32_t HAL_I2C_GetError(const I2C_HandleTypeDef *hi2c) +{ + return hi2c->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup I2C_Private_Functions + * @{ + */ + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint16_t devaddress; + uint32_t tmpITFlags = ITFlags; + + /* Process Locked */ + __HAL_LOCK(hi2c); + + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set corresponding Error Code */ + /* No need to generate STOP, it is automatically done */ + /* Error callback will be send during stop flag treatment */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET)) + { + /* Remove RXNE flag on temporary variable as read done */ + tmpITFlags &= ~I2C_FLAG_RXNE; + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TC) == RESET) && \ + ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET))) + { + /* Write data to TXDR */ + if (hi2c->XferCount != 0U) + { + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TCR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + devaddress = (uint16_t)(hi2c->Instance->CR2 & I2C_CR2_SADD); + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + if (hi2c->XferOptions != I2C_NO_OPTION_FRAME) + { + I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, + hi2c->XferOptions, I2C_NO_STARTSTOP); + } + else + { + I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, + I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); + } + } + } + else + { + /* Call TxCpltCallback() if no stop mode is set */ + if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE) + { + /* Call I2C Master Sequential complete process */ + I2C_ITMasterSeqCplt(hi2c); + } + else + { + /* Wrong size Status regarding TCR flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TC) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + if (hi2c->XferCount == 0U) + { + if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE) + { + /* Generate a stop condition in case of no transfer option */ + if (hi2c->XferOptions == I2C_NO_OPTION_FRAME) + { + /* Generate Stop */ + hi2c->Instance->CR2 |= I2C_CR2_STOP; + } + else + { + /* Call I2C Master Sequential complete process */ + I2C_ITMasterSeqCplt(hi2c); + } + } + } + else + { + /* Wrong size Status regarding TC flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + else + { + /* Nothing to do */ + } + + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Master complete process */ + I2C_ITMasterCplt(hi2c, tmpITFlags); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Memory Mode with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Mem_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint32_t direction = I2C_GENERATE_START_WRITE; + uint32_t tmpITFlags = ITFlags; + + /* Process Locked */ + __HAL_LOCK(hi2c); + + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set corresponding Error Code */ + /* No need to generate STOP, it is automatically done */ + /* Error callback will be send during stop flag treatment */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET)) + { + /* Remove RXNE flag on temporary variable as read done */ + tmpITFlags &= ~I2C_FLAG_RXNE; + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET)) + { + if (hi2c->Memaddress == 0xFFFFFFFFU) + { + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + } + else + { + /* Write LSB part of Memory Address */ + hi2c->Instance->TXDR = hi2c->Memaddress; + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TCR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U)) + { + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_RELOAD_MODE, I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); + } + } + else + { + /* Wrong size Status regarding TCR flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TC) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + /* Disable Interrupt related to address step */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + /* Enable ERR, TC, STOP, NACK and RXI interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT); + + if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + direction = I2C_GENERATE_START_READ; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_RELOAD_MODE, direction); + } + else + { + hi2c->XferSize = hi2c->XferCount; + + /* Set NBYTES to write and generate RESTART */ + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_AUTOEND_MODE, direction); + } + } + else + { + /* Nothing to do */ + } + + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Master complete process */ + I2C_ITMasterCplt(hi2c, tmpITFlags); + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with Interrupt. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint32_t tmpoptions = hi2c->XferOptions; + uint32_t tmpITFlags = ITFlags; + + /* Process locked */ + __HAL_LOCK(hi2c); + + /* Check if STOPF is set */ + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Slave complete process */ + I2C_ITSlaveCplt(hi2c, tmpITFlags); + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Check that I2C transfer finished */ + /* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ + /* Mean XferCount == 0*/ + /* So clear Flag NACKF only */ + if (hi2c->XferCount == 0U) + { + if ((hi2c->State == HAL_I2C_STATE_LISTEN) && (tmpoptions == I2C_FIRST_AND_LAST_FRAME)) + /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for + Warning[Pa134]: left and right operands are identical */ + { + /* Call I2C Listen complete process */ + I2C_ITListenCplt(hi2c, tmpITFlags); + } + else if ((hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) && (tmpoptions != I2C_NO_OPTION_FRAME)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Last Byte is Transmitted */ + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + else + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + } + } + else + { + /* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/ + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + if ((tmpoptions == I2C_FIRST_FRAME) || (tmpoptions == I2C_NEXT_FRAME)) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, hi2c->ErrorCode); + } + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET)) + { + if (hi2c->XferCount > 0U) + { + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferSize--; + hi2c->XferCount--; + } + + if ((hi2c->XferCount == 0U) && \ + (tmpoptions != I2C_NO_OPTION_FRAME)) + { + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_ADDR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_ADDRI) != RESET)) + { + I2C_ITAddrCplt(hi2c, tmpITFlags); + } + else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET)) + { + /* Write data to TXDR only if XferCount not reach "0" */ + /* A TXIS flag can be set, during STOP treatment */ + /* Check if all Data have already been sent */ + /* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */ + if (hi2c->XferCount > 0U) + { + /* Write data to TXDR */ + hi2c->Instance->TXDR = *hi2c->pBuffPtr; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + hi2c->XferCount--; + hi2c->XferSize--; + } + else + { + if ((tmpoptions == I2C_NEXT_FRAME) || (tmpoptions == I2C_FIRST_FRAME)) + { + /* Last Byte is Transmitted */ + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + } + } + else + { + /* Nothing to do */ + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with DMA. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint16_t devaddress; + uint32_t xfermode; + + /* Process Locked */ + __HAL_LOCK(hi2c); + + if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set corresponding Error Code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + /* No need to generate STOP, it is automatically done */ + /* But enable STOP interrupt, to treat it */ + /* Error callback will be send during stop flag treatment */ + I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TCR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + /* Disable TC interrupt */ + __HAL_I2C_DISABLE_IT(hi2c, I2C_IT_TCI); + + if (hi2c->XferCount != 0U) + { + /* Recover Slave address */ + devaddress = (uint16_t)(hi2c->Instance->CR2 & I2C_CR2_SADD); + + /* Prepare the new XferSize to transfer */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + xfermode = I2C_RELOAD_MODE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + if (hi2c->XferOptions != I2C_NO_OPTION_FRAME) + { + xfermode = hi2c->XferOptions; + } + else + { + xfermode = I2C_AUTOEND_MODE; + } + } + + /* Set the new XferSize in Nbytes register */ + I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, xfermode, I2C_NO_STARTSTOP); + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Enable DMA Request */ + if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + } + else + { + /* Call TxCpltCallback() if no stop mode is set */ + if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE) + { + /* Call I2C Master Sequential complete process */ + I2C_ITMasterSeqCplt(hi2c); + } + else + { + /* Wrong size Status regarding TCR flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TC) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + if (hi2c->XferCount == 0U) + { + if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE) + { + /* Generate a stop condition in case of no transfer option */ + if (hi2c->XferOptions == I2C_NO_OPTION_FRAME) + { + /* Generate Stop */ + hi2c->Instance->CR2 |= I2C_CR2_STOP; + } + else + { + /* Call I2C Master Sequential complete process */ + I2C_ITMasterSeqCplt(hi2c); + } + } + } + else + { + /* Wrong size Status regarding TC flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Master complete process */ + I2C_ITMasterCplt(hi2c, ITFlags); + } + else + { + /* Nothing to do */ + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Memory Mode with DMA. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Mem_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint32_t direction = I2C_GENERATE_START_WRITE; + + /* Process Locked */ + __HAL_LOCK(hi2c); + + if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set corresponding Error Code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + /* No need to generate STOP, it is automatically done */ + /* But enable STOP interrupt, to treat it */ + /* Error callback will be send during stop flag treatment */ + I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TXIS) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET)) + { + /* Write LSB part of Memory Address */ + hi2c->Instance->TXDR = hi2c->Memaddress; + + /* Reset Memaddress content */ + hi2c->Memaddress = 0xFFFFFFFFU; + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TCR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + /* Disable Interrupt related to address step */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + /* Enable only Error interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + if (hi2c->XferCount != 0U) + { + /* Prepare the new XferSize to transfer */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_RELOAD_MODE, I2C_NO_STARTSTOP); + } + else + { + hi2c->XferSize = hi2c->XferCount; + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_AUTOEND_MODE, I2C_NO_STARTSTOP); + } + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Enable DMA Request */ + if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + } + else + { + /* Wrong size Status regarding TCR flag event */ + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE); + } + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TC) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET)) + { + /* Disable Interrupt related to address step */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + /* Enable only Error and NACK interrupt for data transfer */ + I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT); + + if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + direction = I2C_GENERATE_START_READ; + } + + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + + /* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */ + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_RELOAD_MODE, direction); + } + else + { + hi2c->XferSize = hi2c->XferCount; + + /* Set NBYTES to write and generate RESTART */ + I2C_TransferConfig(hi2c, (uint16_t)hi2c->Devaddress, (uint8_t)hi2c->XferSize, + I2C_AUTOEND_MODE, direction); + } + + /* Update XferCount value */ + hi2c->XferCount -= hi2c->XferSize; + + /* Enable DMA Request */ + if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + hi2c->Instance->CR1 |= I2C_CR1_RXDMAEN; + } + else + { + hi2c->Instance->CR1 |= I2C_CR1_TXDMAEN; + } + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Master complete process */ + I2C_ITMasterCplt(hi2c, ITFlags); + } + else + { + /* Nothing to do */ + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with DMA. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param ITFlags Interrupt flags to handle. + * @param ITSources Interrupt sources enabled. + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, + uint32_t ITSources) +{ + uint32_t tmpoptions = hi2c->XferOptions; + uint32_t treatdmanack = 0U; + HAL_I2C_StateTypeDef tmpstate; + + /* Process locked */ + __HAL_LOCK(hi2c); + + /* Check if STOPF is set */ + if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET)) + { + /* Call I2C Slave complete process */ + I2C_ITSlaveCplt(hi2c, ITFlags); + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET)) + { + /* Check that I2C transfer finished */ + /* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ + /* Mean XferCount == 0 */ + /* So clear Flag NACKF only */ + if ((I2C_CHECK_IT_SOURCE(ITSources, I2C_CR1_TXDMAEN) != RESET) || + (I2C_CHECK_IT_SOURCE(ITSources, I2C_CR1_RXDMAEN) != RESET)) + { + /* Split check of hdmarx, for MISRA compliance */ + if (hi2c->hdmarx != NULL) + { + if (I2C_CHECK_IT_SOURCE(ITSources, I2C_CR1_RXDMAEN) != RESET) + { + if (I2C_GET_DMA_REMAIN_DATA(hi2c->hdmarx) == 0U) + { + treatdmanack = 1U; + } + } + } + + /* Split check of hdmatx, for MISRA compliance */ + if (hi2c->hdmatx != NULL) + { + if (I2C_CHECK_IT_SOURCE(ITSources, I2C_CR1_TXDMAEN) != RESET) + { + if (I2C_GET_DMA_REMAIN_DATA(hi2c->hdmatx) == 0U) + { + treatdmanack = 1U; + } + } + } + + if (treatdmanack == 1U) + { + if ((hi2c->State == HAL_I2C_STATE_LISTEN) && (tmpoptions == I2C_FIRST_AND_LAST_FRAME)) + /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for + Warning[Pa134]: left and right operands are identical */ + { + /* Call I2C Listen complete process */ + I2C_ITListenCplt(hi2c, ITFlags); + } + else if ((hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) && (tmpoptions != I2C_NO_OPTION_FRAME)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Last Byte is Transmitted */ + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + else + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + } + } + else + { + /* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/ + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + /* Store current hi2c->State, solve MISRA2012-Rule-13.5 */ + tmpstate = hi2c->State; + + if ((tmpoptions == I2C_FIRST_FRAME) || (tmpoptions == I2C_NEXT_FRAME)) + { + if ((tmpstate == HAL_I2C_STATE_BUSY_TX) || (tmpstate == HAL_I2C_STATE_BUSY_TX_LISTEN)) + { + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_TX; + } + else if ((tmpstate == HAL_I2C_STATE_BUSY_RX) || (tmpstate == HAL_I2C_STATE_BUSY_RX_LISTEN)) + { + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_RX; + } + else + { + /* Do nothing */ + } + + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, hi2c->ErrorCode); + } + } + } + else + { + /* Only Clear NACK Flag, no DMA treatment is pending */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + } + } + else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_ADDR) != RESET) && \ + (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_ADDRI) != RESET)) + { + I2C_ITAddrCplt(hi2c, ITFlags); + } + else + { + /* Nothing to do */ + } + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; +} + +/** + * @brief Master sends target device address followed by internal memory address for write request. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, + uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, + uint32_t Tickstart) +{ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); + + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Send Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + } + /* If Memory address size is 16Bit */ + else + { + /* Send MSB of Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Send LSB of Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + } + + /* Wait until TCR flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @brief Master sends target device address followed by internal memory address for read request. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param DevAddress Target device address: The device 7 bits address value + * in datasheet must be shifted to the left before calling the interface + * @param MemAddress Internal memory address + * @param MemAddSize Size of internal memory address + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, + uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, + uint32_t Tickstart) +{ + I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE); + + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* If Memory address size is 8Bit */ + if (MemAddSize == I2C_MEMADD_SIZE_8BIT) + { + /* Send Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + } + /* If Memory address size is 16Bit */ + else + { + /* Send MSB of Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress); + + /* Wait until TXIS flag is set */ + if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Send LSB of Memory Address */ + hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress); + } + + /* Wait until TC flag is set */ + if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TC, RESET, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @brief I2C Address complete process callback. + * @param hi2c I2C handle. + * @param ITFlags Interrupt flags to handle. + * @retval None + */ +static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) +{ + uint8_t transferdirection; + uint16_t slaveaddrcode; + uint16_t ownadd1code; + uint16_t ownadd2code; + + /* Prevent unused argument(s) compilation warning */ + UNUSED(ITFlags); + + /* In case of Listen state, need to inform upper layer of address match code event */ + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) == (uint32_t)HAL_I2C_STATE_LISTEN) + { + transferdirection = I2C_GET_DIR(hi2c); + slaveaddrcode = I2C_GET_ADDR_MATCH(hi2c); + ownadd1code = I2C_GET_OWN_ADDRESS1(hi2c); + ownadd2code = I2C_GET_OWN_ADDRESS2(hi2c); + + /* If 10bits addressing mode is selected */ + if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT) + { + if ((slaveaddrcode & SLAVE_ADDR_MSK) == ((ownadd1code >> SLAVE_ADDR_SHIFT) & SLAVE_ADDR_MSK)) + { + slaveaddrcode = ownadd1code; + hi2c->AddrEventCount++; + if (hi2c->AddrEventCount == 2U) + { + /* Reset Address Event counter */ + hi2c->AddrEventCount = 0U; + + /* Clear ADDR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call Slave Addr callback */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->AddrCallback(hi2c, transferdirection, slaveaddrcode); +#else + HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + } + else + { + slaveaddrcode = ownadd2code; + + /* Disable ADDR Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call Slave Addr callback */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->AddrCallback(hi2c, transferdirection, slaveaddrcode); +#else + HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + } + /* else 7 bits addressing mode is selected */ + else + { + /* Disable ADDR Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call Slave Addr callback */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->AddrCallback(hi2c, transferdirection, slaveaddrcode); +#else + HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + } + /* Else clear address flag only */ + else + { + /* Clear ADDR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + } +} + +/** + * @brief I2C Master sequential complete process. + * @param hi2c I2C handle. + * @retval None + */ +static void I2C_ITMasterSeqCplt(I2C_HandleTypeDef *hi2c) +{ + /* Reset I2C handle mode */ + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* No Generate Stop, to permit restart mode */ + /* The stop will be done at the end of transfer, when I2C_AUTOEND_MODE enable */ + if (hi2c->State == HAL_I2C_STATE_BUSY_TX) + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_TX; + hi2c->XferISR = NULL; + + /* Disable Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MasterTxCpltCallback(hi2c); +#else + HAL_I2C_MasterTxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + /* hi2c->State == HAL_I2C_STATE_BUSY_RX */ + else + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_RX; + hi2c->XferISR = NULL; + + /* Disable Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MasterRxCpltCallback(hi2c); +#else + HAL_I2C_MasterRxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } +} + +/** + * @brief I2C Slave sequential complete process. + * @param hi2c I2C handle. + * @retval None + */ +static void I2C_ITSlaveSeqCplt(I2C_HandleTypeDef *hi2c) +{ + uint32_t tmpcr1value = READ_REG(hi2c->Instance->CR1); + + /* Reset I2C handle mode */ + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* If a DMA is ongoing, Update handle size context */ + if (I2C_CHECK_IT_SOURCE(tmpcr1value, I2C_CR1_TXDMAEN) != RESET) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + } + else if (I2C_CHECK_IT_SOURCE(tmpcr1value, I2C_CR1_RXDMAEN) != RESET) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + } + else + { + /* Do nothing */ + } + + if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) + { + /* Remove HAL_I2C_STATE_SLAVE_BUSY_TX, keep only HAL_I2C_STATE_LISTEN */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_TX; + + /* Disable Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->SlaveTxCpltCallback(hi2c); +#else + HAL_I2C_SlaveTxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN) + { + /* Remove HAL_I2C_STATE_SLAVE_BUSY_RX, keep only HAL_I2C_STATE_LISTEN */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_RX; + + /* Disable Interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->SlaveRxCpltCallback(hi2c); +#else + HAL_I2C_SlaveRxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + else + { + /* Nothing to do */ + } +} + +/** + * @brief I2C Master complete process. + * @param hi2c I2C handle. + * @param ITFlags Interrupt flags to handle. + * @retval None + */ +static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) +{ + uint32_t tmperror; + uint32_t tmpITFlags = ITFlags; + __IO uint32_t tmpreg; + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Disable Interrupts and Store Previous state */ + if (hi2c->State == HAL_I2C_STATE_BUSY_TX) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT); + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_TX; + } + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT); + hi2c->PreviousState = I2C_STATE_MASTER_BUSY_RX; + } + else + { + /* Do nothing */ + } + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + /* Reset handle parameters */ + hi2c->XferISR = NULL; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + + if (I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set acknowledge error code */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + } + + /* Fetch Last receive data if any */ + if ((hi2c->State == HAL_I2C_STATE_ABORT) && (I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET)) + { + /* Read data from RXDR */ + tmpreg = (uint8_t)hi2c->Instance->RXDR; + UNUSED(tmpreg); + } + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Store current volatile hi2c->ErrorCode, misra rule */ + tmperror = hi2c->ErrorCode; + + /* Call the corresponding callback to inform upper layer of End of Transfer */ + if ((hi2c->State == HAL_I2C_STATE_ABORT) || (tmperror != HAL_I2C_ERROR_NONE)) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, hi2c->ErrorCode); + } + /* hi2c->State == HAL_I2C_STATE_BUSY_TX */ + else if (hi2c->State == HAL_I2C_STATE_BUSY_TX) + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + if (hi2c->Mode == HAL_I2C_MODE_MEM) + { + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MemTxCpltCallback(hi2c); +#else + HAL_I2C_MemTxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + else + { + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MasterTxCpltCallback(hi2c); +#else + HAL_I2C_MasterTxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + } + /* hi2c->State == HAL_I2C_STATE_BUSY_RX */ + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + if (hi2c->Mode == HAL_I2C_MODE_MEM) + { + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MemRxCpltCallback(hi2c); +#else + HAL_I2C_MemRxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + else + { + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->MasterRxCpltCallback(hi2c); +#else + HAL_I2C_MasterRxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + } + else + { + /* Nothing to do */ + } +} + +/** + * @brief I2C Slave complete process. + * @param hi2c I2C handle. + * @param ITFlags Interrupt flags to handle. + * @retval None + */ +static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) +{ + uint32_t tmpcr1value = READ_REG(hi2c->Instance->CR1); + uint32_t tmpITFlags = ITFlags; + uint32_t tmpoptions = hi2c->XferOptions; + HAL_I2C_StateTypeDef tmpstate = hi2c->State; + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Disable Interrupts and Store Previous state */ + if ((tmpstate == HAL_I2C_STATE_BUSY_TX) || (tmpstate == HAL_I2C_STATE_BUSY_TX_LISTEN)) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT); + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_TX; + } + else if ((tmpstate == HAL_I2C_STATE_BUSY_RX) || (tmpstate == HAL_I2C_STATE_BUSY_RX_LISTEN)) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT); + hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_RX; + } + else if (tmpstate == HAL_I2C_STATE_LISTEN) + { + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_TX_IT | I2C_XFER_RX_IT); + hi2c->PreviousState = I2C_STATE_NONE; + } + else + { + /* Do nothing */ + } + + /* Disable Address Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* If a DMA is ongoing, Update handle size context */ + if (I2C_CHECK_IT_SOURCE(tmpcr1value, I2C_CR1_TXDMAEN) != RESET) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + if (hi2c->hdmatx != NULL) + { + hi2c->XferCount = (uint16_t)I2C_GET_DMA_REMAIN_DATA(hi2c->hdmatx); + } + } + else if (I2C_CHECK_IT_SOURCE(tmpcr1value, I2C_CR1_RXDMAEN) != RESET) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + if (hi2c->hdmarx != NULL) + { + hi2c->XferCount = (uint16_t)I2C_GET_DMA_REMAIN_DATA(hi2c->hdmarx); + } + } + else + { + /* Do nothing */ + } + + /* Store Last receive data if any */ + if (I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) + { + /* Remove RXNE flag on temporary variable as read done */ + tmpITFlags &= ~I2C_FLAG_RXNE; + + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + if ((hi2c->XferSize > 0U)) + { + hi2c->XferSize--; + hi2c->XferCount--; + } + } + + /* All data are not transferred, so set error code accordingly */ + if (hi2c->XferCount != 0U) + { + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + } + + if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \ + (I2C_CHECK_IT_SOURCE(tmpcr1value, I2C_IT_NACKI) != RESET)) + { + /* Check that I2C transfer finished */ + /* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */ + /* Mean XferCount == 0*/ + /* So clear Flag NACKF only */ + if (hi2c->XferCount == 0U) + { + if ((hi2c->State == HAL_I2C_STATE_LISTEN) && (tmpoptions == I2C_FIRST_AND_LAST_FRAME)) + /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for + Warning[Pa134]: left and right operands are identical */ + { + /* Call I2C Listen complete process */ + I2C_ITListenCplt(hi2c, tmpITFlags); + } + else if ((hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) && (tmpoptions != I2C_NO_OPTION_FRAME)) + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Last Byte is Transmitted */ + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + else + { + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + } + } + else + { + /* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/ + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + + if ((tmpoptions == I2C_FIRST_FRAME) || (tmpoptions == I2C_NEXT_FRAME)) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, hi2c->ErrorCode); + } + } + } + + hi2c->Mode = HAL_I2C_MODE_NONE; + hi2c->XferISR = NULL; + + if (hi2c->ErrorCode != HAL_I2C_ERROR_NONE) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, hi2c->ErrorCode); + + /* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */ + if (hi2c->State == HAL_I2C_STATE_LISTEN) + { + /* Call I2C Listen complete process */ + I2C_ITListenCplt(hi2c, tmpITFlags); + } + } + else if (hi2c->XferOptions != I2C_NO_OPTION_FRAME) + { + /* Call the Sequential Complete callback, to inform upper layer of the end of Transfer */ + I2C_ITSlaveSeqCplt(hi2c); + + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->ListenCpltCallback(hi2c); +#else + HAL_I2C_ListenCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + /* Call the corresponding callback to inform upper layer of End of Transfer */ + else if (hi2c->State == HAL_I2C_STATE_BUSY_RX) + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->SlaveRxCpltCallback(hi2c); +#else + HAL_I2C_SlaveRxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + else + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->SlaveTxCpltCallback(hi2c); +#else + HAL_I2C_SlaveTxCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } +} + +/** + * @brief I2C Listen complete process. + * @param hi2c I2C handle. + * @param ITFlags Interrupt flags to handle. + * @retval None + */ +static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags) +{ + /* Reset handle parameters */ + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->PreviousState = I2C_STATE_NONE; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + hi2c->XferISR = NULL; + + /* Store Last receive data if any */ + if (I2C_CHECK_FLAG(ITFlags, I2C_FLAG_RXNE) != RESET) + { + /* Read data from RXDR */ + *hi2c->pBuffPtr = (uint8_t)hi2c->Instance->RXDR; + + /* Increment Buffer pointer */ + hi2c->pBuffPtr++; + + if ((hi2c->XferSize > 0U)) + { + hi2c->XferSize--; + hi2c->XferCount--; + + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + } + } + + /* Disable all Interrupts*/ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT | I2C_XFER_TX_IT); + + /* Clear NACK Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->ListenCpltCallback(hi2c); +#else + HAL_I2C_ListenCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ +} + +/** + * @brief I2C interrupts error process. + * @param hi2c I2C handle. + * @param ErrorCode Error code to handle. + * @retval None + */ +static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode) +{ + HAL_I2C_StateTypeDef tmpstate = hi2c->State; + + uint32_t tmppreviousstate; + + /* Reset handle parameters */ + hi2c->Mode = HAL_I2C_MODE_NONE; + hi2c->XferOptions = I2C_NO_OPTION_FRAME; + hi2c->XferCount = 0U; + + /* Set new error code */ + hi2c->ErrorCode |= ErrorCode; + + /* Disable Interrupts */ + if ((tmpstate == HAL_I2C_STATE_LISTEN) || + (tmpstate == HAL_I2C_STATE_BUSY_TX_LISTEN) || + (tmpstate == HAL_I2C_STATE_BUSY_RX_LISTEN)) + { + /* Disable all interrupts, except interrupts related to LISTEN state */ + I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_TX_IT); + + /* keep HAL_I2C_STATE_LISTEN if set */ + hi2c->State = HAL_I2C_STATE_LISTEN; + hi2c->XferISR = I2C_Slave_ISR_IT; + } + else + { + /* Disable all interrupts */ + I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT | I2C_XFER_RX_IT | I2C_XFER_TX_IT); + + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* If state is an abort treatment on going, don't change state */ + /* This change will be do later */ + if (hi2c->State != HAL_I2C_STATE_ABORT) + { + /* Set HAL_I2C_STATE_READY */ + hi2c->State = HAL_I2C_STATE_READY; + + /* Check if a STOPF is detected */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == SET) + { + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == SET) + { + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + hi2c->ErrorCode |= HAL_I2C_ERROR_AF; + } + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + } + + } + hi2c->XferISR = NULL; + } + + /* Abort DMA TX transfer if any */ + tmppreviousstate = hi2c->PreviousState; + + if ((hi2c->hdmatx != NULL) && ((tmppreviousstate == I2C_STATE_MASTER_BUSY_TX) || \ + (tmppreviousstate == I2C_STATE_SLAVE_BUSY_TX))) + { + if ((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + } + + if (HAL_DMA_GetState(hi2c->hdmatx) != HAL_DMA_STATE_READY) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx); + } + } + else + { + I2C_TreatErrorCallback(hi2c); + } + } + /* Abort DMA RX transfer if any */ + else if ((hi2c->hdmarx != NULL) && ((tmppreviousstate == I2C_STATE_MASTER_BUSY_RX) || \ + (tmppreviousstate == I2C_STATE_SLAVE_BUSY_RX))) + { + if ((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN) + { + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + } + + if (HAL_DMA_GetState(hi2c->hdmarx) != HAL_DMA_STATE_READY) + { + /* Set the I2C DMA Abort callback : + will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */ + hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK) + { + /* Call Directly hi2c->hdmarx->XferAbortCallback function in case of error */ + hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx); + } + } + else + { + I2C_TreatErrorCallback(hi2c); + } + } + else + { + I2C_TreatErrorCallback(hi2c); + } +} + +/** + * @brief I2C Error callback treatment. + * @param hi2c I2C handle. + * @retval None + */ +static void I2C_TreatErrorCallback(I2C_HandleTypeDef *hi2c) +{ + if (hi2c->State == HAL_I2C_STATE_ABORT) + { + hi2c->State = HAL_I2C_STATE_READY; + hi2c->PreviousState = I2C_STATE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->AbortCpltCallback(hi2c); +#else + HAL_I2C_AbortCpltCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } + else + { + hi2c->PreviousState = I2C_STATE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + /* Call the corresponding callback to inform upper layer of End of Transfer */ +#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1) + hi2c->ErrorCallback(hi2c); +#else + HAL_I2C_ErrorCallback(hi2c); +#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */ + } +} + +/** + * @brief I2C Tx data register flush process. + * @param hi2c I2C handle. + * @retval None + */ +static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c) +{ + /* If a pending TXIS flag is set */ + /* Write a dummy data in TXDR to clear it */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) != RESET) + { + hi2c->Instance->TXDR = 0x00U; + } + + /* Flush TX register if not empty */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXE) == RESET) + { + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_TXE); + } +} + +/** + * @brief DMA I2C master transmit process complete callback. + * @param hdma DMA handle + * @retval None + */ +static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma) +{ + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + /* If last transfer, enable STOP interrupt */ + if (hi2c->XferCount == 0U) + { + /* Enable STOP interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); + } + /* else prepare a new DMA transfer and enable TCReload interrupt */ + else + { + /* Update Buffer pointer */ + hi2c->pBuffPtr += hi2c->XferSize; + + /* Set the XferSize to transfer */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + } + + /* Enable the DMA stream or channel depends on Instance */ + if (HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR, + hi2c->XferSize) != HAL_OK) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_DMA); + } + else + { + /* Enable TC interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT); + } + } +} + + +/** + * @brief DMA I2C slave transmit process complete callback. + * @param hdma DMA handle + * @retval None + */ +static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma) +{ + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + uint32_t tmpoptions = hi2c->XferOptions; + + if ((tmpoptions == I2C_NEXT_FRAME) || (tmpoptions == I2C_FIRST_FRAME)) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN; + + /* Last Byte is Transmitted */ + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + else + { + /* No specific action, Master fully manage the generation of STOP condition */ + /* Mean that this generation can arrive at any time, at the end or during DMA process */ + /* So STOP condition should be manage through Interrupt treatment */ + } +} + + +/** + * @brief DMA I2C master receive process complete callback. + * @param hdma DMA handle + * @retval None + */ +static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma) +{ + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + /* If last transfer, enable STOP interrupt */ + if (hi2c->XferCount == 0U) + { + /* Enable STOP interrupt */ + I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT); + } + /* else prepare a new DMA transfer and enable TCReload interrupt */ + else + { + /* Update Buffer pointer */ + hi2c->pBuffPtr += hi2c->XferSize; + + /* Set the XferSize to transfer */ + if (hi2c->XferCount > MAX_NBYTE_SIZE) + { + hi2c->XferSize = MAX_NBYTE_SIZE; + } + else + { + hi2c->XferSize = hi2c->XferCount; + } + + /* Enable the DMA stream or channel depends on Instance */ + if (HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)hi2c->pBuffPtr, + hi2c->XferSize) != HAL_OK) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_DMA); + } + else + { + /* Enable TC interrupts */ + I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT); + } + } +} + + +/** + * @brief DMA I2C slave receive process complete callback. + * @param hdma DMA handle + * @retval None + */ +static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma) +{ + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + uint32_t tmpoptions = hi2c->XferOptions; + + if ((I2C_GET_DMA_REMAIN_DATA(hi2c->hdmarx) == 0U) && \ + (tmpoptions != I2C_NO_OPTION_FRAME)) + { + /* Disable DMA Request */ + hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN; + + /* Call I2C Slave Sequential complete process */ + I2C_ITSlaveSeqCplt(hi2c); + } + else + { + /* No specific action, Master fully manage the generation of STOP condition */ + /* Mean that this generation can arrive at any time, at the end or during DMA process */ + /* So STOP condition should be manage through Interrupt treatment */ + } +} + + +/** + * @brief DMA I2C communication error callback. + * @param hdma DMA handle + * @retval None + */ +static void I2C_DMAError(DMA_HandleTypeDef *hdma) +{ + uint32_t treatdmaerror = 0U; + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + + if (hi2c->hdmatx != NULL) + { + if (I2C_GET_DMA_REMAIN_DATA(hi2c->hdmatx) == 0U) + { + treatdmaerror = 1U; + } + } + + if (hi2c->hdmarx != NULL) + { + if (I2C_GET_DMA_REMAIN_DATA(hi2c->hdmarx) == 0U) + { + treatdmaerror = 1U; + } + } + + /* Check if a FIFO error is detected, if true normal use case, so no specific action to perform */ + if (!((HAL_DMA_GetError(hdma) == HAL_DMA_ERROR_FE)) && (treatdmaerror != 0U)) + { + /* Disable Acknowledge */ + hi2c->Instance->CR2 |= I2C_CR2_NACK; + + /* Call the corresponding callback to inform upper layer of End of Transfer */ + I2C_ITError(hi2c, HAL_I2C_ERROR_DMA); + } +} + + +/** + * @brief DMA I2C communication abort callback + * (To be called at end of DMA Abort procedure). + * @param hdma DMA handle. + * @retval None + */ +static void I2C_DMAAbort(DMA_HandleTypeDef *hdma) +{ + /* Derogation MISRAC2012-Rule-11.5 */ + I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); + + /* Reset AbortCpltCallback */ + if (hi2c->hdmatx != NULL) + { + hi2c->hdmatx->XferAbortCallback = NULL; + } + if (hi2c->hdmarx != NULL) + { + hi2c->hdmarx->XferAbortCallback = NULL; + } + + I2C_TreatErrorCallback(hi2c); +} + + +/** + * @brief This function handles I2C Communication Timeout. It waits + * until a flag is no longer in the specified status. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param Flag Specifies the I2C flag to check. + * @param Status The actual Flag status (SET or RESET). + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, + uint32_t Timeout, uint32_t Tickstart) +{ + while (__HAL_I2C_GET_FLAG(hi2c, Flag) == Status) + { + /* Check if an error is detected */ + if (I2C_IsErrorOccurred(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - Tickstart) > Timeout) || (Timeout == 0U)) + { + if ((__HAL_I2C_GET_FLAG(hi2c, Flag) == Status)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + return HAL_ERROR; + } + } + } + } + return HAL_OK; +} + +/** + * @brief This function handles I2C Communication Timeout for specific usage of TXIS flag. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart) +{ + while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) == RESET) + { + /* Check if an error is detected */ + if (I2C_IsErrorOccurred(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - Tickstart) > Timeout) || (Timeout == 0U)) + { + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) == RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + } + } + return HAL_OK; +} + +/** + * @brief This function handles I2C Communication Timeout for specific usage of STOP flag. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart) +{ + while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) + { + /* Check if an error is detected */ + if (I2C_IsErrorOccurred(hi2c, Timeout, Tickstart) != HAL_OK) + { + return HAL_ERROR; + } + + /* Check for the Timeout */ + if (((HAL_GetTick() - Tickstart) > Timeout) || (Timeout == 0U)) + { + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_ERROR; + } + } + } + return HAL_OK; +} + +/** + * @brief This function handles I2C Communication Timeout for specific usage of RXNE flag. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, + uint32_t Tickstart) +{ + HAL_StatusTypeDef status = HAL_OK; + + while ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == RESET) && (status == HAL_OK)) + { + /* Check if an error is detected */ + if (I2C_IsErrorOccurred(hi2c, Timeout, Tickstart) != HAL_OK) + { + status = HAL_ERROR; + } + + /* Check if a STOPF is detected */ + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == SET) && (status == HAL_OK)) + { + /* Check if an RXNE is pending */ + /* Store Last receive data if any */ + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == SET) && (hi2c->XferSize > 0U)) + { + /* Return HAL_OK */ + /* The Reading of data from RXDR will be done in caller function */ + status = HAL_OK; + } + + /* Check a no-acknowledge have been detected */ + if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == SET) + { + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + hi2c->ErrorCode = HAL_I2C_ERROR_AF; + + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + status = HAL_ERROR; + } + else + { + hi2c->ErrorCode = HAL_I2C_ERROR_NONE; + } + } + + /* Check for the Timeout */ + if ((((HAL_GetTick() - Tickstart) > Timeout) || (Timeout == 0U)) && (status == HAL_OK)) + { + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == RESET)) + { + hi2c->ErrorCode |= HAL_I2C_ERROR_TIMEOUT; + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + status = HAL_ERROR; + } + } + } + return status; +} + +/** + * @brief This function handles errors detection during an I2C Communication. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param Timeout Timeout duration + * @param Tickstart Tick start value + * @retval HAL status + */ +static HAL_StatusTypeDef I2C_IsErrorOccurred(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart) +{ + HAL_StatusTypeDef status = HAL_OK; + uint32_t itflag = hi2c->Instance->ISR; + uint32_t error_code = 0; + uint32_t tickstart = Tickstart; + uint32_t tmp1; + HAL_I2C_ModeTypeDef tmp2; + + if (HAL_IS_BIT_SET(itflag, I2C_FLAG_AF)) + { + /* Clear NACKF Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF); + + /* Wait until STOP Flag is set or timeout occurred */ + /* AutoEnd should be initiate after AF */ + while ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) && (status == HAL_OK)) + { + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + tmp1 = (uint32_t)(hi2c->Instance->CR2 & I2C_CR2_STOP); + tmp2 = hi2c->Mode; + + /* In case of I2C still busy, try to regenerate a STOP manually */ + if ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) != RESET) && \ + (tmp1 != I2C_CR2_STOP) && \ + (tmp2 != HAL_I2C_MODE_SLAVE)) + { + /* Generate Stop */ + hi2c->Instance->CR2 |= I2C_CR2_STOP; + + /* Update Tick with new reference */ + tickstart = HAL_GetTick(); + } + + while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) + { + /* Check for the Timeout */ + if ((HAL_GetTick() - tickstart) > I2C_TIMEOUT_STOPF) + { + error_code |= HAL_I2C_ERROR_TIMEOUT; + + status = HAL_ERROR; + + break; + } + } + } + } + } + + /* In case STOP Flag is detected, clear it */ + if (status == HAL_OK) + { + /* Clear STOP Flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF); + } + + error_code |= HAL_I2C_ERROR_AF; + + status = HAL_ERROR; + } + + /* Refresh Content of Status register */ + itflag = hi2c->Instance->ISR; + + /* Then verify if an additional errors occurs */ + /* Check if a Bus error occurred */ + if (HAL_IS_BIT_SET(itflag, I2C_FLAG_BERR)) + { + error_code |= HAL_I2C_ERROR_BERR; + + /* Clear BERR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_BERR); + + status = HAL_ERROR; + } + + /* Check if an Over-Run/Under-Run error occurred */ + if (HAL_IS_BIT_SET(itflag, I2C_FLAG_OVR)) + { + error_code |= HAL_I2C_ERROR_OVR; + + /* Clear OVR flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_OVR); + + status = HAL_ERROR; + } + + /* Check if an Arbitration Loss error occurred */ + if (HAL_IS_BIT_SET(itflag, I2C_FLAG_ARLO)) + { + error_code |= HAL_I2C_ERROR_ARLO; + + /* Clear ARLO flag */ + __HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ARLO); + + status = HAL_ERROR; + } + + if (status != HAL_OK) + { + /* Flush TX register */ + I2C_Flush_TXDR(hi2c); + + /* Clear Configuration Register 2 */ + I2C_RESET_CR2(hi2c); + + hi2c->ErrorCode |= error_code; + hi2c->State = HAL_I2C_STATE_READY; + hi2c->Mode = HAL_I2C_MODE_NONE; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + } + + return status; +} + +/** + * @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). + * @param hi2c I2C handle. + * @param DevAddress Specifies the slave address to be programmed. + * @param Size Specifies the number of bytes to be programmed. + * This parameter must be a value between 0 and 255. + * @param Mode New state of the I2C START condition generation. + * This parameter can be one of the following values: + * @arg @ref I2C_RELOAD_MODE Enable Reload mode . + * @arg @ref I2C_AUTOEND_MODE Enable Automatic end mode. + * @arg @ref I2C_SOFTEND_MODE Enable Software end mode. + * @param Request New state of the I2C START condition generation. + * This parameter can be one of the following values: + * @arg @ref I2C_NO_STARTSTOP Don't Generate stop and start condition. + * @arg @ref I2C_GENERATE_STOP Generate stop condition (Size should be set to 0). + * @arg @ref I2C_GENERATE_START_READ Generate Restart for read request. + * @arg @ref I2C_GENERATE_START_WRITE Generate Restart for write request. + * @retval None + */ +static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, + uint32_t Request) +{ + uint32_t tmp; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); + assert_param(IS_TRANSFER_MODE(Mode)); + assert_param(IS_TRANSFER_REQUEST(Request)); + + /* Declaration of tmp to prevent undefined behavior of volatile usage */ + tmp = ((uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | \ + (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | \ + (uint32_t)Mode | (uint32_t)Request) & (~0x80000000U)); + + /* update CR2 register */ + MODIFY_REG(hi2c->Instance->CR2, \ + ((I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | \ + (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31U - I2C_CR2_RD_WRN_Pos))) | \ + I2C_CR2_START | I2C_CR2_STOP)), tmp); +} + +/** + * @brief Manage the enabling of Interrupts. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param InterruptRequest Value of @ref I2C_Interrupt_configuration_definition. + * @retval None + */ +static void I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest) +{ + uint32_t tmpisr = 0U; + + if ((hi2c->XferISR != I2C_Master_ISR_DMA) && \ + (hi2c->XferISR != I2C_Slave_ISR_DMA) && \ + (hi2c->XferISR != I2C_Mem_ISR_DMA)) + { + if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) + { + /* Enable ERR, STOP, NACK and ADDR interrupts */ + tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; + } + + if ((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT) + { + /* Enable ERR, TC, STOP, NACK and TXI interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_TXI; + } + + if ((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT) + { + /* Enable ERR, TC, STOP, NACK and RXI interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_RXI; + } + + if (InterruptRequest == I2C_XFER_ERROR_IT) + { + /* Enable ERR and NACK interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_NACKI; + } + + if (InterruptRequest == I2C_XFER_CPLT_IT) + { + /* Enable STOP interrupts */ + tmpisr |= I2C_IT_STOPI; + } + } + + else + { + if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) + { + /* Enable ERR, STOP, NACK and ADDR interrupts */ + tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; + } + + if ((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT) + { + /* Enable ERR, TC, STOP, NACK and TXI interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_TXI; + } + + if ((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT) + { + /* Enable ERR, TC, STOP, NACK and RXI interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_RXI; + } + + if (InterruptRequest == I2C_XFER_ERROR_IT) + { + /* Enable ERR and NACK interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_NACKI; + } + + if (InterruptRequest == I2C_XFER_CPLT_IT) + { + /* Enable STOP interrupts */ + tmpisr |= (I2C_IT_STOPI | I2C_IT_TCI); + } + + if (InterruptRequest == I2C_XFER_RELOAD_IT) + { + /* Enable TC interrupts */ + tmpisr |= I2C_IT_TCI; + } + } + + /* Enable interrupts only at the end */ + /* to avoid the risk of I2C interrupt handle execution before */ + /* all interrupts requested done */ + __HAL_I2C_ENABLE_IT(hi2c, tmpisr); +} + +/** + * @brief Manage the disabling of Interrupts. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2C. + * @param InterruptRequest Value of @ref I2C_Interrupt_configuration_definition. + * @retval None + */ +static void I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest) +{ + uint32_t tmpisr = 0U; + + if ((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT) + { + /* Disable TC and TXI interrupts */ + tmpisr |= I2C_IT_TCI | I2C_IT_TXI; + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) != (uint32_t)HAL_I2C_STATE_LISTEN) + { + /* Disable NACK and STOP interrupts */ + tmpisr |= I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; + } + } + + if ((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT) + { + /* Disable TC and RXI interrupts */ + tmpisr |= I2C_IT_TCI | I2C_IT_RXI; + + if (((uint32_t)hi2c->State & (uint32_t)HAL_I2C_STATE_LISTEN) != (uint32_t)HAL_I2C_STATE_LISTEN) + { + /* Disable NACK and STOP interrupts */ + tmpisr |= I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; + } + } + + if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT) + { + /* Disable ADDR, NACK and STOP interrupts */ + tmpisr |= I2C_IT_ADDRI | I2C_IT_STOPI | I2C_IT_NACKI | I2C_IT_ERRI; + } + + if (InterruptRequest == I2C_XFER_ERROR_IT) + { + /* Enable ERR and NACK interrupts */ + tmpisr |= I2C_IT_ERRI | I2C_IT_NACKI; + } + + if (InterruptRequest == I2C_XFER_CPLT_IT) + { + /* Enable STOP interrupts */ + tmpisr |= I2C_IT_STOPI; + } + + if (InterruptRequest == I2C_XFER_RELOAD_IT) + { + /* Enable TC interrupts */ + tmpisr |= I2C_IT_TCI; + } + + /* Disable interrupts only at the end */ + /* to avoid a breaking situation like at "t" time */ + /* all disable interrupts request are not done */ + __HAL_I2C_DISABLE_IT(hi2c, tmpisr); +} + +/** + * @brief Convert I2Cx OTHER_xxx XferOptions to functional XferOptions. + * @param hi2c I2C handle. + * @retval None + */ +static void I2C_ConvertOtherXferOptions(I2C_HandleTypeDef *hi2c) +{ + /* if user set XferOptions to I2C_OTHER_FRAME */ + /* it request implicitly to generate a restart condition */ + /* set XferOptions to I2C_FIRST_FRAME */ + if (hi2c->XferOptions == I2C_OTHER_FRAME) + { + hi2c->XferOptions = I2C_FIRST_FRAME; + } + /* else if user set XferOptions to I2C_OTHER_AND_LAST_FRAME */ + /* it request implicitly to generate a restart condition */ + /* then generate a stop condition at the end of transfer */ + /* set XferOptions to I2C_FIRST_AND_LAST_FRAME */ + else if (hi2c->XferOptions == I2C_OTHER_AND_LAST_FRAME) + { + hi2c->XferOptions = I2C_FIRST_AND_LAST_FRAME; + } + else + { + /* Nothing to do */ + } +} + +/** + * @} + */ + +#endif /* HAL_I2C_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ Index: ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c_ex.c =================================================================== --- ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c_ex.c (revision 88) +++ ctrl/firmware/Main/CubeMX/Drivers/STM32H7xx_HAL_Driver/Src/stm32h7xx_hal_i2c_ex.c (revision 88) @@ -0,0 +1,372 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_i2c_ex.c + * @author MCD Application Team + * @brief I2C Extended HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of I2C Extended peripheral: + * + Filter Mode Functions + * + WakeUp Mode Functions + * + FastModePlus Functions + * + ****************************************************************************** + * @attention + * + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + @verbatim + ============================================================================== + ##### I2C peripheral Extended features ##### + ============================================================================== + + [..] Comparing to other previous devices, the I2C interface for STM32H7xx + devices contains the following additional features + + (+) Possibility to disable or enable Analog Noise Filter + (+) Use of a configured Digital Noise Filter + (+) Disable or enable wakeup from Stop mode(s) + (+) Disable or enable Fast Mode Plus + + ##### How to use this driver ##### + ============================================================================== + [..] This driver provides functions to configure Noise Filter and Wake Up Feature + (#) Configure I2C Analog noise filter using the function HAL_I2CEx_ConfigAnalogFilter() + (#) Configure I2C Digital noise filter using the function HAL_I2CEx_ConfigDigitalFilter() + (#) Configure the enable or disable of I2C Wake Up Mode using the functions : + (++) HAL_I2CEx_EnableWakeUp() + (++) HAL_I2CEx_DisableWakeUp() + (#) Configure the enable or disable of fast mode plus driving capability using the functions : + (++) HAL_I2CEx_EnableFastModePlus() + (++) HAL_I2CEx_DisableFastModePlus() + @endverbatim + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32h7xx_hal.h" + +/** @addtogroup STM32H7xx_HAL_Driver + * @{ + */ + +/** @defgroup I2CEx I2CEx + * @brief I2C Extended HAL module driver + * @{ + */ + +#ifdef HAL_I2C_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup I2CEx_Exported_Functions I2C Extended Exported Functions + * @{ + */ + +/** @defgroup I2CEx_Exported_Functions_Group1 Filter Mode Functions + * @brief Filter Mode Functions + * +@verbatim + =============================================================================== + ##### Filter Mode Functions ##### + =============================================================================== + [..] This section provides functions allowing to: + (+) Configure Noise Filters + +@endverbatim + * @{ + */ + +/** + * @brief Configure I2C Analog noise filter. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2Cx peripheral. + * @param AnalogFilter New state of the Analog filter. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); + assert_param(IS_I2C_ANALOG_FILTER(AnalogFilter)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the selected I2C peripheral */ + __HAL_I2C_DISABLE(hi2c); + + /* Reset I2Cx ANOFF bit */ + hi2c->Instance->CR1 &= ~(I2C_CR1_ANFOFF); + + /* Set analog filter bit*/ + hi2c->Instance->CR1 |= AnalogFilter; + + __HAL_I2C_ENABLE(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Configure I2C Digital noise filter. + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2Cx peripheral. + * @param DigitalFilter Coefficient of digital noise filter between Min_Data=0x00 and Max_Data=0x0F. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter) +{ + uint32_t tmpreg; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance)); + assert_param(IS_I2C_DIGITAL_FILTER(DigitalFilter)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the selected I2C peripheral */ + __HAL_I2C_DISABLE(hi2c); + + /* Get the old register value */ + tmpreg = hi2c->Instance->CR1; + + /* Reset I2Cx DNF bits [11:8] */ + tmpreg &= ~(I2C_CR1_DNF); + + /* Set I2Cx DNF coefficient */ + tmpreg |= DigitalFilter << 8U; + + /* Store the new register value */ + hi2c->Instance->CR1 = tmpreg; + + __HAL_I2C_ENABLE(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} +/** + * @} + */ + +/** @defgroup I2CEx_Exported_Functions_Group2 WakeUp Mode Functions + * @brief WakeUp Mode Functions + * +@verbatim + =============================================================================== + ##### WakeUp Mode Functions ##### + =============================================================================== + [..] This section provides functions allowing to: + (+) Configure Wake Up Feature + +@endverbatim + * @{ + */ + +/** + * @brief Enable I2C wakeup from Stop mode(s). + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2Cx peripheral. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c) +{ + /* Check the parameters */ + assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the selected I2C peripheral */ + __HAL_I2C_DISABLE(hi2c); + + /* Enable wakeup from stop mode */ + hi2c->Instance->CR1 |= I2C_CR1_WUPEN; + + __HAL_I2C_ENABLE(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Disable I2C wakeup from Stop mode(s). + * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains + * the configuration information for the specified I2Cx peripheral. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c) +{ + /* Check the parameters */ + assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance)); + + if (hi2c->State == HAL_I2C_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hi2c); + + hi2c->State = HAL_I2C_STATE_BUSY; + + /* Disable the selected I2C peripheral */ + __HAL_I2C_DISABLE(hi2c); + + /* Enable wakeup from stop mode */ + hi2c->Instance->CR1 &= ~(I2C_CR1_WUPEN); + + __HAL_I2C_ENABLE(hi2c); + + hi2c->State = HAL_I2C_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hi2c); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} +/** + * @} + */ + +/** @defgroup I2CEx_Exported_Functions_Group3 Fast Mode Plus Functions + * @brief Fast Mode Plus Functions + * +@verbatim + =============================================================================== + ##### Fast Mode Plus Functions ##### + =============================================================================== + [..] This section provides functions allowing to: + (+) Configure Fast Mode Plus + +@endverbatim + * @{ + */ + +/** + * @brief Enable the I2C fast mode plus driving capability. + * @param ConfigFastModePlus Selects the pin. + * This parameter can be one of the @ref I2CEx_FastModePlus values + * @note For I2C1, fast mode plus driving capability can be enabled on all selected + * I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently + * on each one of the following pins PB6, PB7, PB8 and PB9. + * @note For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability + * can be enabled only by using I2C_FASTMODEPLUS_I2C1 parameter. + * @note For all I2C2 pins fast mode plus driving capability can be enabled + * only by using I2C_FASTMODEPLUS_I2C2 parameter. + * @note For all I2C3 pins fast mode plus driving capability can be enabled + * only by using I2C_FASTMODEPLUS_I2C3 parameter. + * @note For all I2C4 pins fast mode plus driving capability can be enabled + * only by using I2C_FASTMODEPLUS_I2C4 parameter. + * @note For all I2C5 pins fast mode plus driving capability can be enabled + * only by using I2C_FASTMODEPLUS_I2C5 parameter. + * @retval None + */ +void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus) +{ + /* Check the parameter */ + assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus)); + + /* Enable SYSCFG clock */ + __HAL_RCC_SYSCFG_CLK_ENABLE(); + + /* Enable fast mode plus driving capability for selected pin */ + SET_BIT(SYSCFG->PMCR, (uint32_t)ConfigFastModePlus); +} + +/** + * @brief Disable the I2C fast mode plus driving capability. + * @param ConfigFastModePlus Selects the pin. + * This parameter can be one of the @ref I2CEx_FastModePlus values + * @note For I2C1, fast mode plus driving capability can be disabled on all selected + * I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently + * on each one of the following pins PB6, PB7, PB8 and PB9. + * @note For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability + * can be disabled only by using I2C_FASTMODEPLUS_I2C1 parameter. + * @note For all I2C2 pins fast mode plus driving capability can be disabled + * only by using I2C_FASTMODEPLUS_I2C2 parameter. + * @note For all I2C3 pins fast mode plus driving capability can be disabled + * only by using I2C_FASTMODEPLUS_I2C3 parameter. + * @note For all I2C4 pins fast mode plus driving capability can be disabled + * only by using I2C_FASTMODEPLUS_I2C4 parameter. + * @note For all I2C5 pins fast mode plus driving capability can be disabled + * only by using I2C_FASTMODEPLUS_I2C5 parameter. + * @retval None + */ +void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus) +{ + /* Check the parameter */ + assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus)); + + /* Enable SYSCFG clock */ + __HAL_RCC_SYSCFG_CLK_ENABLE(); + + /* Disable fast mode plus driving capability for selected pin */ + CLEAR_BIT(SYSCFG->PMCR, (uint32_t)ConfigFastModePlus); +} +/** + * @} + */ +/** + * @} + */ + +#endif /* HAL_I2C_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ Index: ctrl/firmware/Main/CubeMX/charger.ioc =================================================================== --- ctrl/firmware/Main/CubeMX/charger.ioc (revision 87) +++ ctrl/firmware/Main/CubeMX/charger.ioc (revision 88) @@ -210,23 +210,24 @@ Mcu.IP0=CORTEX_M7 Mcu.IP1=DEBUG -Mcu.IP10=SDMMC1 -Mcu.IP11=SPI2 -Mcu.IP12=SPI4 -Mcu.IP13=SYS -Mcu.IP14=TIM3 -Mcu.IP15=TIM6 -Mcu.IP16=TIM8 -Mcu.IP17=USART2 -Mcu.IP18=USART3 -Mcu.IP19=USART10 +Mcu.IP10=RTC +Mcu.IP11=SDMMC1 +Mcu.IP12=SPI2 +Mcu.IP13=SPI4 +Mcu.IP14=SYS +Mcu.IP15=TIM3 +Mcu.IP16=TIM6 +Mcu.IP17=TIM8 +Mcu.IP18=USART2 +Mcu.IP19=USART3 Mcu.IP2=DMA +Mcu.IP20=USART10 Mcu.IP3=FATFS Mcu.IP4=FREERTOS -Mcu.IP5=MDMA -Mcu.IP6=MEMORYMAP -Mcu.IP7=NVIC -Mcu.IP8=RCC -Mcu.IP9=RTC -Mcu.IPNb=20 +Mcu.IP5=I2C1 +Mcu.IP6=MDMA +Mcu.IP7=MEMORYMAP +Mcu.IP8=NVIC +Mcu.IP9=RCC +Mcu.IPNb=21 Mcu.Name=STM32H723ZETx Mcu.Package=LQFP144 @@ -277,21 +278,23 @@ Mcu.Pin49=PB4(NJTRST) Mcu.Pin5=PH0-OSC_IN -Mcu.Pin50=PB8 -Mcu.Pin51=PB9 -Mcu.Pin52=VP_FATFS_VS_SDIO -Mcu.Pin53=VP_FREERTOS_VS_CMSIS_V2 -Mcu.Pin54=VP_RTC_VS_RTC_Activate -Mcu.Pin55=VP_RTC_VS_RTC_Calendar -Mcu.Pin56=VP_SYS_VS_tim7 -Mcu.Pin57=VP_TIM3_VS_ClockSourceINT -Mcu.Pin58=VP_TIM6_VS_ClockSourceINT -Mcu.Pin59=VP_TIM8_VS_ControllerModeReset +Mcu.Pin50=PB6 +Mcu.Pin51=PB7 +Mcu.Pin52=PB8 +Mcu.Pin53=PB9 +Mcu.Pin54=VP_FATFS_VS_SDIO +Mcu.Pin55=VP_FREERTOS_VS_CMSIS_V2 +Mcu.Pin56=VP_RTC_VS_RTC_Activate +Mcu.Pin57=VP_RTC_VS_RTC_Calendar +Mcu.Pin58=VP_SYS_VS_tim7 +Mcu.Pin59=VP_TIM3_VS_ClockSourceINT Mcu.Pin6=PH1-OSC_OUT -Mcu.Pin60=VP_TIM8_VS_ClockSourceINT -Mcu.Pin61=VP_MEMORYMAP_VS_MEMORYMAP +Mcu.Pin60=VP_TIM6_VS_ClockSourceINT +Mcu.Pin61=VP_TIM8_VS_ControllerModeReset +Mcu.Pin62=VP_TIM8_VS_ClockSourceINT +Mcu.Pin63=VP_MEMORYMAP_VS_MEMORYMAP Mcu.Pin7=PF15 Mcu.Pin8=PG0 Mcu.Pin9=PG1 -Mcu.PinsNb=62 +Mcu.PinsNb=64 Mcu.ThirdParty0=STMicroelectronics.X-CUBE-AZRTOS-H7.3.3.0 Mcu.ThirdPartyNb=1 @@ -395,4 +398,14 @@ PB4(NJTRST).PinState=GPIO_PIN_SET PB4(NJTRST).Signal=GPIO_Output +PB6.GPIOParameters=GPIO_Label +PB6.GPIO_Label=BME_I2C_SCL +PB6.Locked=true +PB6.Mode=I2C +PB6.Signal=I2C1_SCL +PB7.GPIOParameters=GPIO_Label +PB7.GPIO_Label=BME_I2C_SDA +PB7.Locked=true +PB7.Mode=I2C +PB7.Signal=I2C1_SDA PB8.GPIOParameters=GPIO_Label,GPIO_ModeDefaultEXTI PB8.GPIO_Label=ETH_SPI_INT @@ -620,5 +633,6 @@ RCC.DIVR2=10 RCC.DIVR2Freq_Value=25000000 -RCC.DIVR3Freq_Value=100000000 +RCC.DIVR3=4 +RCC.DIVR3Freq_Value=50000000 RCC.FDCANFreq_Value=100000000 RCC.FMCFreq_Value=100000000 @@ -626,12 +640,13 @@ RCC.HCLK3ClockFreq_Value=100000000 RCC.HCLKFreq_Value=100000000 -RCC.I2C123Freq_Value=100000000 +RCC.I2C123CLockSelection=RCC_I2C1235CLKSOURCE_HSI +RCC.I2C123Freq_Value=64000000 RCC.I2C4Freq_Value=100000000 -RCC.IPParameters=ADCFreq_Value,AHB12Freq_Value,AHB4Freq_Value,APB1Freq_Value,APB2Freq_Value,APB3Freq_Value,APB4Freq_Value,AXIClockFreq_Value,CECFreq_Value,CKPERFreq_Value,CortexFreq_Value,CpuClockFreq_Value,D1CPREFreq_Value,DFSDMACLkFreq_Value,DFSDMFreq_Value,DIVM1,DIVM2,DIVM3,DIVN1,DIVN2,DIVN3,DIVP1Freq_Value,DIVP2Freq_Value,DIVP3Freq_Value,DIVQ1Freq_Value,DIVQ2,DIVQ2Freq_Value,DIVQ3,DIVQ3Freq_Value,DIVR1Freq_Value,DIVR2,DIVR2Freq_Value,DIVR3Freq_Value,FDCANFreq_Value,FMCFreq_Value,FamilyName,HCLK3ClockFreq_Value,HCLKFreq_Value,I2C123Freq_Value,I2C4Freq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPTIM345Freq_Value,LPUART1Freq_Value,LTDCFreq_Value,MCO1PinFreq_Value,MCO2PinFreq_Value,PLL2FRACN,PLL2_VCI_Range-AdvancedSettings,PLLFRACN,PLLSourceVirtual,QSPIFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI4AFreq_Value,SAI4BFreq_Value,SDMMCFreq_Value,SPDIFRXFreq_Value,SPI123CLockSelection,SPI123Freq_Value,SPI45Freq_Value,SPI6Freq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,Spi45ClockSelection,Tim1OutputFreq_Value,Tim2OutputFreq_Value,TraceFreq_Value,USART16CLockSelection,USART16Freq_Value,USART234578CLockSelection,USART234578Freq_Value,USBFreq_Value,VCO1OutputFreq_Value,VCO2OutputFreq_Value,VCO3OutputFreq_Value,VCOInput1Freq_Value,VCOInput2Freq_Value,VCOInput3Freq_Value +RCC.IPParameters=ADCFreq_Value,AHB12Freq_Value,AHB4Freq_Value,APB1Freq_Value,APB2Freq_Value,APB3Freq_Value,APB4Freq_Value,AXIClockFreq_Value,CECFreq_Value,CKPERFreq_Value,CortexFreq_Value,CpuClockFreq_Value,D1CPREFreq_Value,DFSDMACLkFreq_Value,DFSDMFreq_Value,DIVM1,DIVM2,DIVM3,DIVN1,DIVN2,DIVN3,DIVP1Freq_Value,DIVP2Freq_Value,DIVP3Freq_Value,DIVQ1Freq_Value,DIVQ2,DIVQ2Freq_Value,DIVQ3,DIVQ3Freq_Value,DIVR1Freq_Value,DIVR2,DIVR2Freq_Value,DIVR3,DIVR3Freq_Value,FDCANFreq_Value,FMCFreq_Value,FamilyName,HCLK3ClockFreq_Value,HCLKFreq_Value,I2C123CLockSelection,I2C123Freq_Value,I2C4Freq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPTIM345Freq_Value,LPUART1Freq_Value,LTDCFreq_Value,MCO1PinFreq_Value,MCO2PinFreq_Value,PLL2FRACN,PLL2_VCI_Range-AdvancedSettings,PLLFRACN,PLLSourceVirtual,QSPIFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI4AFreq_Value,SAI4BFreq_Value,SDMMCFreq_Value,SPDIFRXFreq_Value,SPI123CLockSelection,SPI123Freq_Value,SPI45Freq_Value,SPI6Freq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,Spi45ClockSelection,Tim1OutputFreq_Value,Tim2OutputFreq_Value,TraceFreq_Value,USART16CLockSelection,USART16Freq_Value,USART234578CLockSelection,USART234578Freq_Value,USBFreq_Value,VCO1OutputFreq_Value,VCO2OutputFreq_Value,VCO3OutputFreq_Value,VCOInput1Freq_Value,VCOInput2Freq_Value,VCOInput3Freq_Value RCC.LPTIM1Freq_Value=100000000 RCC.LPTIM2Freq_Value=100000000 RCC.LPTIM345Freq_Value=100000000 RCC.LPUART1Freq_Value=100000000 -RCC.LTDCFreq_Value=100000000 +RCC.LTDCFreq_Value=50000000 RCC.MCO1PinFreq_Value=64000000 RCC.MCO2PinFreq_Value=100000000